This part of the a cylinder holds the piston in place and helps support the rod as it extends. a. rod seals b. rod bushing c. pistons seals d. rod brushing

Q: Question: To install the front cover on an engine, position its either on the or on the cover…

A: A gasket is a flat rubber piece that fills the space between two metal surfaces in the engine or…

Q: 126) Technician A says all gaskets should be discarded during teardown to keep the work area clean.…

A: According to the technician A , all the gaskets should be discarded during teardown ,it is not…

Q: Conside: the liquid flowing in the tank shown in the figure. The height (h) of the liquid is 3m.…

A: Given Data The height of the liquid is: h=3 m To Find The velocity at point 2 Use the Bernaulli's…

Q: Why must a cylinder ridge be removed before attempting to remove the piston?

A: Cylinder ridge reamer is a component use to remove the ridge.

Q: Can I get some help looking over some sheets? I have most filled out, but just to double check for…

A: During four stroke the crankshaft turns twice — moving each piston up and down twice — while the…

Q: What is the best option for removing a stuck coolant hose? Select one: a. Twisting the hose off with…

A: A technician's primary responsibility is to prevent vehicle breakdowns. Cooling system failures are…

Q: the rim and face alighnment method is a.used only to alighn solid flange couplings b.less accurate…

A: Rim and face method is also called the dial indicator method. it consists of the installment of two…

Q: Hello, I have some diagrams I have filled out for practice that I would like to use to study for an…

A: I have gone through alll your answers in the first part, and upto my knowledge all your answer seems…

Q: Technician A says all gaskets should be discarded during teardown to keep the work area clean.…

A: Gasket : A gasket is a mechanical seal i.e it is used to close up the gap between two mating…

Q: Define the term the radius of the pedestal?

A: The pedestal is basically a compression member used as a support for columns or other structures

Q: When trying to accommodate only axial loading, which of the following bearings is most likely to be…

A: (a) Tapered roller bearing This type of bearing is used in the places where, vertical and horizontal…

Q: What volume of oil to the cylinder is required to cause the cylinder to advance at a speed of 392…

A: Given Data: The speed of advance of the cylinder is, C=392 in/min. The diameter of the piston is,…

Q: Hello, I have some diagrams I have filled out for practice that I would like to use to study for an…

A: Diagram 1. E - relief valve A- gear pump D- rotor F- internal gear C- internal and external gear…

Q: A __________ hook has an eye at a right angle to the plane of the hook. Select one: A. FOUNDRY B.…

A: Given :-  A __________ hook has an eye at a right angle to the plane of the hook. Select one: A.…

Q: What material is the piston? None of these answers are correct Steel Cast iron O Aluminum

A: Given:   To select the correct option for the material of the piston.

Q: Task 5 - Brake Callipers and Discs Brake callipers and discs, like the braking system are different…

A: given; (1) examine the example caliper  and examine the material used? (2) How many piston are used…

Q: to provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the…

A: Question:- To provide a good sealing joint between the cylinder head and exhaust, apply a sealant to…

Q: A STAR WHEEL ADJUSTER RETURN SPRINGS ANCHOR PLATE E ANCHOR PIN PLATE SPRING SPRING STAR WHEEL…

A: Backing plate - C Shoe - D Wheel cylinder - A

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: A kick is defined as an unplanned formation fluid entry into the wellbore annulus. a. True b. False

A: A kick tends to occurs in  oil well when the pressure exerted by the rock surrounding the bore is…

Q: When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat…

A: The reconditioning of the valve seats is done to remove cracks, pitting and grooves from its…

Q: Draw free body diagram and kinetic diagram for Counterweight Box, Swing arm and sling please draw…

A: Given: A diagram of trebuchet To find: Free body diagram and kinetic diagram: Counterweight box…

Q: Why does a free-to-move piston hold a constant pressure in the cylinder?

A: Free-to-move piston is the one in which the friction is zero and the atmospheric pressure outside…

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.