5. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the shaft and key is 40 MPa and the number of bolts connecting the two halves are 4. The permissible tensile stress for the bolts material is 70 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3. [Ans. d = 55 mm; D = 125 mm; L=192.5 mm; d = 24 mm] 720

5. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the shaft and key is 40 MPa and the number of bolts connecting the two halves are 4. The permissible tensile stress for the bolts material is 70 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3. [Ans. d = 55 mm; D = 125 mm; L=192.5 mm; d = 24 mm] 720

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If you are Sure then Only Attempt.
PROBLEM: A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in diameter and 92 mm hub length. Six 16-mm bolts in a 165-mm diameter bolts circle connect the flanges. The keyway is 6 mm shorter than the hub length and the key is 14 mm x 14 mm. Coupling is to transmit 45 kW at 160 rpm. For all parts, yield point value in shear is one-half the yield point value in tension or compression that is 448 MPa. Find a) the shearing stress of key and its factor of safety; b) the bearing stress of key and the factor of safety based on yield point; c) the shearing stress in bolts and factor of safety based on yield point. (Board problem, November 1983) 14 mm x 14 mm x 86 mm d = 16 mm Dr = 111 mm D= 57 mm Dp = 165 mm w = 50 mm 92 mm Dimensions in mm
A flange coupling having 180 mm bolt circle and 19 mm thick uses 12 bolts, 16 mm diameter to connect two shafts. It is used to transmit 80 Hp at 180 rpm. Determine the factor of safety in bearing if yield point in compression is 65 ksi.
Q.1 Design a compression coupling for a shaft to transmit 2000 N-m. The allowable shear stress for the shaft and key is 50 MPa and the number of bolts connecting the two halves are 6. The permissible tensile stress for the bolt material is 90 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
8. A cross belt arrangement has centre distance between pulleys as 1.5 m. The diameter of bigger and smaller pulleys are 'D' and 'd' respectively. The smaller pulley rotates at 1000 r.p.m. and the bigger pulley at 500 r.p.m. The flat belt is 6 mm thick and transmits 7.5 kW power at belt speed of 13 m/s approximately. The coefficient of belt friction is 0.3 and the density of belt material is 950 kg/m³. If the permissible tensile stress for the belt material is 1.75 MPa, calculate: 1. Diameters of pulleys; 2. Length and width of belt. [Ans. 500 mm, 250 mm ; 4.272 m, 90 mm]
Situational Problem ( 3 - 4) An automobile engine develops 33.5 hp at 1,000 rpm. The clutch used to transmit this power in a single plate clutch with two pairs of contact surfaces. The coefficient of friction is 0.4 and the mean diameter of the disk is to be 190 mm. The average normal stress on the clutch lining is 120 kPa. 3. Determine the axial force to engage the clutch based on uniform wear. A. 1.57 kN B. 3.14 kN C. 5.28 kN D. 7.46 kN
Design a bushed-pin type flexible coupling for connecting a motor shaft to a pump shaft for the following service conditions : Power to be transmitted = 40 kW ; speed of the motor shaft = 1000 r.p.m. ; diameter of the motor shaft = 50 mm ; diameter of the pump shaft = 45 mm. The bearing pressure in the rubber bush and allowable stress in the pins are to be limited to 0.45 N/mm2 and 25 MPa respectively. %3D !! [Ans. d, = 20 mm; n = 6; d, = 40 mm ;l = 152 mm] !3! COO01
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
Q3-a/ What are the characteristics of material which used for lining friction surfaces of a clutch? (5Marks) b/ An engine developing 45 kW at 1000 r.p.m. is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 12.5° and a maximum mean diameter of 500 mm. The coefficient of friction is 0.2. The normal pressure on the clutch face is not to exceed (0.1 N/mm2). Determine: 1. The face width required, and 2. The axial spring force necessary to engage the clutch Answer question 4 or 5 (15 Marks) 15 Q4/ The areas of the turning moment diagram for one revolution of a multi-cylinder engine with reference to the mean turning moment, below and above the line, are - 32, + 408,-267, +333,-310, +226,- 374, + 260 and 244 mm². The scale for abscissa and ordinate are: 1 mm = 2.4° and 1 mm = 650 N-m respectively. The mean speed is 300 r.p.m. with a percentage speed fluctuation of± 1.5%. If the hoop stress in the material of the rim is not to exceed 5.6 MPa, determine the…