A cone clutch with cone angle 20° is to transmit 7.5 kW at 750 r.p.m. The normal intensity of pressure between the contact faces is not to exceed 0.12 N/mm². The coefficient of friction is 0.2. If face width is ½th of mean diameter, find : 1. the main dimensions of the clutch, and 2. axial force required while running. [Ans. R = 117 mm ; b = 46.8 mm ; r₁ = 125 mm ; r₂ = 109 mm; 1395 N]

A cone clutch with cone angle 20° is to transmit 7.5 kW at 750 r.p.m. The normal intensity of pressure between the contact faces is not to exceed 0.12 N/mm². The coefficient of friction is 0.2. If face width is ½th of mean diameter, find : 1. the main dimensions of the clutch, and 2. axial force required while running. [Ans. R = 117 mm ; b = 46.8 mm ; r₁ = 125 mm ; r₂ = 109 mm; 1395 N]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A cone clutch for industrial use is to transmit 15 hp at 400 rpm. The mean diameter of the clutch is…

Q: How to get mu=0.366. Show calculation fast.

A: Given : T1 = 30 KN T2 = 30000 KN n = 3 To find : how to get coefficient of friction as 0.366

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

Q: A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the system has a…

A: The power transmitted, P = 4 kWThe diameter of the smaller pulley, d = 150 mmThe speed of the…

Q: A conical clutch has an included angle of 150. The outer and inner diameters are 100 and 40 mm…

A: Given data:Since, the clutch is of two halves.So, the cone angle of the clutch isOuter diameter,…

Q: Find the brake power of the engine running at 755 rpm. The iength of lever from centre of pulley is…

A: We need to figure out how much braking power the engine has at 755 rpm.The lever is 1.43 metres long…

Q: An automobile single plate ciutch consists of a pair of contacting surtaces. The inneOr and outer…

Q: mm, The semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque required…

A: A disc or plate clutch has the same use that a cone clutch has. Instead of two spinning discs, the…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10° The width of…

A: Given, Power transmitted , P =10 Kw Speed, N =600 rpm Cone angle = 10 degree maximum pressure , Pr…

Q: (A) If the power losses in Pelton wheel due to bucket friction is given by 1 POK (V, -u) where K is…

Q: Consider the arrangement of a simple band brake as shown in the figure. Determine the brake torque…

Q: Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The…

A: C=5 mD=3 md=3 mTmax=4 KNμ=0.3N=700 rpmVelocity of belt, V=π*d*N60V=π*3*70060=109.95 m/s

Q: Q. A multi disc clutch has 5 plates having four pairs Myd of active friction surfaces. If the…

A: The solution is given in next step

Q: A conical clutch has an inclined angle of 120. The outer and inner diameters are 80 mm and 20 mm…

A: The answer is given in the following step

Q: Two pulleys with diameters (450 mm) and (200 mm), centre distance (1.95 m). if we use cross belt…

Q: ch. The friction lining has a ce 25. The bore radius of friction li ilom contLacl pressur of IMI

Q: A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10◦ The width of the…

A: Given data:

Q: The torque (in Nm)

A: Given data: Forces F1 and F2 in a brake band and the direction of rotation of the drum are shown in…

Q: The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given: The torque on the drum, T = 5 ft.lb The coefficient of friction between belt and drum, μ =…

Q: 1. A uniform ladder of mass m and length is leaning at rest against a wall at an angle 0. The…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Given: Q=14,361.60gpm L=1000ft D=2ft hf=12.58ft. Determine the friction

A: Given Discharge, Q = 14361.60 gpm = 0.91 m3/s Length, L = 1000 ft = 304.8 m…

Q: A cone clutch has D = 16 in, d = 14 in, a cone length of 3 in, and a coefficient of friction of…

Q: Consider a brake testing bench as shown in the figure. Motor 16.1 50 20 Clutch + X A motor speeds up…

Q: A friction clutch is to transmit 10 kW at 3000 rpm. It is to be of single plate type with both sides…

Q: Determine the (a) The face width in millimeters. (b) Pressure in the left-hand shoe in (kPa). (c)…

A: Given DataR=170mmμ=0.3F=2800NPm=1050kPaρ=150mmf=130°

Q: The band of a brake has a contact angle of 18° deg. If the pulls on the bands are 275 kg and 100 kg,…

Q: braké shown below, the drum diameter is 16 inches, the coefficient of friction is 0.25, and the drum…

A: Given: Diameter of the drum (D)=16in or 0.4064m Tension on tight side (T1)=1000lb Tension on slack…

Q: Exomple: An automotive single-plate clutch with o pairs of frichon Surfaces, tvansmits a 300. N-m…

A: For single plate clutch : Torque (T)=300 N-m speed (N)= 1500 rpm inner dia.(d) = 170 mm outer…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

19.
A cone clutch with cone angle 20° is to transmit 7.5 kW at 750 r.p.m. The normal intensity of pressure
between the contact faces is not to exceed 0.12 N/mm². The coefficient of friction is 0.2. If face width
is ½th of mean diameter, find : 1. the main dimensions of the clutch, and 2. axial force required
while running.
[Ans. R = 117 mm ; b = 46.8 mm ; r₁ = 125 mm; r₂ = 109 mm; 1395 N]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Calculation

VIEW

Step 3: Conclusion

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q/The layout of a crossed leather belt drive is shown in Fig. below. The belt, transmits 7.5 kW and operates at a velocity of 13 m/s approximately. The coefficient of friction is 0.3 and the permissible tensile stress for the belt material is 1.75 N/mm2. Calculate (i) The diameters of pulleys; (ii) The length of the belt and (iii) Belt tensions on the tight and slack sides. 500 грm 1000 грm d1 d2 -1500 mm-
A CONE CLUTCH WITH CONE ANGL€ 20 IS TO TRANSMIT 7.5KW AT 750 8 P.m. THE NORMAL IN TENSITY OR PRESSURE BETWEEN THE CONTACT CACES IS NOT T O EXCEED 0-12N Imm? THE COEFEICIENT OF FRICTI(ON IS 0.2.1E FACE WID TH IS TH OF MEAN DIAMETER, FIND a) THE mAIN DIMENSIONS OF CLUTH AND (b) AXIAL FORCE REQUIRED whILE RUNNING
Crate coef of static friction is .55, what is min force to prevent slipping, what is min force to prevent tipping
Q2/ A conical clutch an included angle of 60°. the outer radius and inner diameters are 80 and 20 cm respectively. Calculate the maximum and minimum intensity of pressure and force required to press the two halves together if it is to transmit 20 MW, at 60 rev/h. the coefficient of friction is 0.3, Use both the uniform wear theory and the uniform pressure theory.
O d. 90 [kN] Clear my choice The crate has a weight of 490 lb and a center of gravity at G rests on the floor for which the coefficient of static friction is equal to 0.3. If the force P = 200 lb is applied as shown in the figure below. The force of friction developed between the crate and the ground is. -2 ft --2 ft- 5. 2 ft 4 ft 3 ft Figure 1 Select one: O a. 160 lb O b. 106 lb O . 601 Ib O d. 610 lb Finish attempt . PREVIOUS ACTIVITY MENG250 - Midterm Exam -Spring 2020-2021 E OA d) ENG 1:03 PM 号 6/9/2021 acer
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
Q3-a/ What are the characteristics of material which used for lining friction surfaces of a clutch? (5Marks) b/ An engine developing 45 kW at 1000 r.p.m. is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 12.5° and a maximum mean diameter of 500 mm. The coefficient of friction is 0.2. The normal pressure on the clutch face is not to exceed (0.1 N/mm2). Determine: 1. The face width required, and 2. The axial spring force necessary to engage the clutch Answer question 4 or 5 (15 Marks) 15 Q4/ The areas of the turning moment diagram for one revolution of a multi-cylinder engine with reference to the mean turning moment, below and above the line, are - 32, + 408,-267, +333,-310, +226,- 374, + 260 and 244 mm². The scale for abscissa and ordinate are: 1 mm = 2.4° and 1 mm = 650 N-m respectively. The mean speed is 300 r.p.m. with a percentage speed fluctuation of± 1.5%. If the hoop stress in the material of the rim is not to exceed 5.6 MPa, determine the…