A cross belt system gives a speed reduction of 6:1 and the centre distance between the pulleys is 2.5 m. The effective radius of the driving pulley is r₂ = 80 mm and it runs at the speed of 550 rpm. The grove angle of pulleys is 25°. The belt has a mass of 0.35 kg/m and the coefficient of friction of 0.3. If the tension in the belt is not to exceed 650 N. calculate the power that can be transmitted by drive.

A cross belt system gives a speed reduction of 6:1 and the centre distance between the pulleys is 2.5 m. The effective radius of the driving pulley is r₂ = 80 mm and it runs at the speed of 550 rpm. The grove angle of pulleys is 25°. The belt has a mass of 0.35 kg/m and the coefficient of friction of 0.3. If the tension in the belt is not to exceed 650 N. calculate the power that can be transmitted by drive.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A multi plate friction clutch is used to transmit the power from the engine to a rotor which has a mass of 152 kg and a radius of gyration of 0.34 m. The inner and outer radius of the clutch disc is 0.055 m and 0.217 m respectively. The clutch plate has 4 contact surfaces (n = 4) and the axial thrust is 379 N. The flywheel of the engine rotates constantly at 1,106 rpm. Calculate the time required to accelerate the rotor from rest if the clutch is suddenly engaged. Take u = 0.42. Assume uniform wear in clutch.
The roughly position of the automobile jack shown in the figure is a square screw with a single blade at both ends. ABC is controlled by a bolt (right-hand threaded in A, left-handed in C). square of the bolt screw has a pitch of 2.5 mm and an average diameter of 9 mm. between the bolt and the jack limbs The coefficient of static friction is 0.15, taking into account the position and load shown, you can use the jack Find the magnitude of the torque that must be applied to raise it.
D B (2 100N AB=10 cm CB=BD=4 cm AF=2cm In the mechanism shown above, the friction coefficient of the sliding limb is given as 0.3. A horizontal force of 100 N is applied from the F point. Calculate the torque required for the AB crank handle to start SYT (Counter Clockwise) motion.
The width of the simple band brake shown in the figure is 30 mm. The coefficient of friction between the brake and the drum surface is 0.20. Determine the braking torque and thickness of the band if the tensile stress is not to exceed 65 N/mm2.
A multi plate friction clutch is used to transmit the power from the engine to a rotor which has a mass of 152 kg and a radius of gyration of 0.34 m. The inner and outer radius of the clutch disc is 0.055 m and 0.217 m respectively. The clutch plate has 4 contact surfaces (n = 4) and the axial thrust is 379 N. The flywheel of the engine rotates constantly at 1,106 rpm. Calculate the time required to accelerate the rotor from rest if the clutch is suddenly engaged. Take μ = 0.42. Assume uniform wear in clutch.
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
8. Answer the following questions about the exercise of Box A (massmA=50kg) and Box B (mB=10kg) located on the slope as shown in Figure 7. Between slope and box A, the coefficient of static friction is uk, and the angle of slope is 10 degrees, although box A and B are connected in a solid line and ignore the mass of the pulley.1)What is the maximum friction (kgf) between Box A and Slope for us=0.4 and Uk=0.15?2)What is the maximum friction between Box A and the slope (kgf) for us=0.3 and UK=0.15?3)us=0.3 and Uk=0.15 What is the tension in kgf?4)us=0.3 and uk=0.15 when box B goes down 2m, calculate the size (m/s) of the speed of box A and box B using the modified energy supply law.
Given: Correction factor f = 0.92, load factor k = 1.2 V-belt profile bxh = 20x12, H = 0.25 For pulleys d01 = 167 mm, d02 = 668 mm Efficiency for belt-pulley n1 = 0.91 Total efficiency for gearbox nmin = 0.95 belt-pulley system is (a) 650 mm, using the figure given according to the belt speed and belt width and using the following data; Q1. Find the forces in the stretched and loose belt arms.
The coefficient of static friction under the block a and b are the same. If the block is in the verge of sliding, find the tension at each chord. Assume that the pulley is frictionless.Recall [from Physics]:?? = ???Where:?? - is the frictional force?? - is the normal force? -coefficient of static frictiona. Determine the tensile force (lb) on the cable 1.b. Determine the tensile force (lb) on the cable 2. Plsss show complete handwritten solution. Thanksss!!
Note: If you don't know the solution please leave it but don't give me wrong solution. A flat open belt drive is used to transmit a power of 25kW from a motor shaft rotating at 950 rpm. The radius of the pulley of the motor shaft is 125mm while the radius of the puller of the driven shaft is 450mm. The center distance between the shafts is 2,250mm. the coefficient of friction is 0.25 and the density of the belt material is 950 kg/m^3. The belt width is 126 mm. The allowable stress is 2.6MPa. Determine the thickness of the belt.
Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner diameter of 125 mm and an outer diameter of 200 mm and the coefficient of friction between mating surfaces is 0.35. It is assumed that shafts of both machines are co-axial and the driving shaft is rotating at a constant speed of 240 rev/min when it is suddenly brought in contact with the driven shaft/machine initially rotating at 20 rev/min. The Moment of Inertia of the driven machine is 21 kgm2. A slippage period of 6.8 sec is observed while the driven machine is brought to the full speed of the driving shaft. Analyse the frictional power transmission and calculate: The magnitude of the torque necessary to cause the described acceleration of the driven shaft :
A 1" diameter line shaft, which is supported by frictionless pulleys at the ends, carries 2 pulleys. The 10" diameter driver pulley is driven in a counter-clockwise direction, and its belt tensions are 25 lbs and 56 lbs. The 2" diameter driven pulley has one of its belt tensions measured at 30 lbs. Calculate the missing belt tension.