not use ai please Problem 4:Voting 2 out of 4 logic is a redundancy scheme utilized in control systemsto enhance reliability. It operates by evaluating four input signals andgenerating a single output based on the majority vote of those inputs.Specifically, the output signal becomes active only when at least two ofthe input signals are active.Inputs: The voting logic requires four input signals (A, B, C, and D),each originating from distinct sources or sensors.☐ Output: A solitary output signal (designated as Y) is produced based onthe majority vote result of the inputs.Logic Gates: The inputs are connected to a series of AND and OR gatesthat implement the 2 out of 4 voting logic.Voting: The logic gates are arranged in such a way that the systemrequires at least two inputs to be in the same state (either high or low) toconsider the input valid.

Approach to solving the question: Detailed explanation: Examples: Key references:

Answered: Problem 4: Voting 2 out of 4 logic is a…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

Question 7 plz provide answer
Design a circuit that controls the passage of a signal "A" with the specifications: 1. Output X will equal A when control B and C are the same 2. X will remain HIGH when B and C are different. Hint: Set "A" input as a CLK pin.
16. What is the two's complement of 1011100111? 17. Explain function of each element in Figure 3. (Register A, B, C, Clock, Carry out,D, C, Q, PRE, S, CI, CO) Subtractor Circuit Register A Register C Register B PRE Carry Out (Sign Bit) CI CO Clock- Figure 3 18. In the Figure 4, Register A is 1011 and Register B is 0010. a. What are the contents of register C after 2 clock pulses? b. What is the output of flip flop (Q) after the second clock pulse? c. What is the output of flip flop (Q) after the third clock pulse? d. What are the contents of register C after 5 clock pulses? Adder Circuit Register A Register C Register B B CLR CI CO Q Clock Figure 4 19. The serial adder required ten clock pulses to add two, five bit binary numbers. (True or false. İf it is false write correct one .) 8.
Question 4) which data shift register does each of the following illustration represent?
Draw a 2x1 multiplexer block diagram.Create the status table. Find the simplest form of circuit output with Karnaugh.Explain the circuit problem that may occur.What should be done to fix the problem?(NEED A NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE)
Task 1: You are to design a 4-bit arithmetic unit that consists of a 4-bit adder/subtractor circuit. The arithmetic unit takes as inputs two 4-bit numbers (A and B) and one control input (M) add/subtract selector that selects the type of operation the unit will perform. When the input control is ‘0’, the input numbers are added. When it is set to ‘1’, the two input numbers are subtracted (A - B)
Please help me to do this
Choose the true H-bridge motor statements in the list below. O The L298N has a PWM input signal that can be used to control the motor direction. (false, it controls the speed of the motor. O You should always transition through the "Off" state when changing direction with the H-bridge. O The H-bridge provides a means of controlling a motors spin direction. O If all four H-bridge switches are open, the motors will spin. O The H-bridge uses four switches to control the current flow.
In ADC, as you increase the number of bits, you can convert analogue signal to digital signal in smaller steps.
Procedure: You are to design a 4-bit arithmetic unit that consists of a 4-bit adder/subtractor circuit. The arithmetic unit takes as inputs two 4-bit numbers (A and B) and one control input (M) add/subtract selector that selects the type of operation the unit will perform. When the input control is ‘0’, the input numbers are added. When it is set to ‘1’, the two input numbers are subtracted (A - B). Question: Two 4-bit Adder/Subtractor Circuit: Design and construct a 4-bit adder/subtractor circuit. Draw the produced circuit.
Choose the false statement. a. In SCR the gate is the controlling terminal b. SCR are used for high-power applications c. SCR is a controlled device d. SCR is a bidirectional device
A person is recording measurements from an analog data reader. During the first reading, he was not looking at the meter from a straight angle. He gets the reading of 72. At a second reading later he looks straight at the machine and gets the reading of 70. a) Which reading number is nearer to the actual value? What is the error type that happened in that reading? b) c) Suppose the data reader becomes faulty due to the extreme heat and gives a third measurement of 65. What type of error happened now? The data reader is working properly now, but there is a slight difference between two readings for the same measure. What type of error happened now and how can we d) minimize it?

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS