In the time domain a circuit has a voltage source with a value of v(t)= 10cos(2000t + 30°) Volts. Answer the following questions a) Convert the voltage source to the phasor domain - that is find V b) If a resistor in the time domain circuit has a value of 1500 ohms, what is the impedance of that resistor in the phasor domain? ZRc) If a capacitor in the time domain circuit has a value of 20µF and an inductor in the time domain circuit has a value of 25mH what is the the impedance of the capacitor and the impedance of the inductor in the phasor domain? That is find ZC and ZL

In the time domain a circuit has a voltage source with a value of v(t)= 10cos(2000t + 30°) Volts. Answer the following questions a) Convert the voltage source to the phasor domain - that is find V b) If a resistor in the time domain circuit has a value of 1500 ohms, what is the impedance of that resistor in the phasor domain? ZRc) If a capacitor in the time domain circuit has a value of 20µF and an inductor in the time domain circuit has a value of 25mH what is the the impedance of the capacitor and the impedance of the inductor in the phasor domain? That is find ZC and ZL

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Similar questions

An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
An electrical circuit with a sinusoidal voltage source, a resistor, and a capacitor all connected in series. The voltage across the capacitor: Select one: a. Leads the current in the capacitor by exactly 90o b. Is in phase with the sinusoidal voltage source c. Is in phase with the voltage across the resistor d. Leads the current in the circuit by 90o e. Lags the current in the circuit by 90o
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)
Curent and voltages phase....
Thanks for answering this question
Shown in the figure below is an "RLC" circuit driven by an AC power source. The AC power source has an RMS voltage of Vps(RMS) = 11.80 Volts and is running at a frequency of f = 147000 Hz. The resistor has a resistance of R = 3910 Ω, the capacitor has a capacitance of C = 4.01e-10 Farads, and the inductor has an inductance of L = 5.97e-03 Henries.Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit ?Ztot = Determine the numerical value of Ztot = ΩDetermine the numerical value of ?Ztot = degreesDetermine the current through the circuit: I(PEAK) = Amps I(RMS) = Amps Determine the voltage across the inductor: VL(PEAK) = Volts VL(RMS) = Volts Determine the voltage across the capacitor: VC(PEAK) = Volts VC(RMS) = Volts If a second circuit were connected in parallel with the resistor, this circuit would be considered as: a high-pass filtera flux capacitor a radio tunera phase…
Please answer the question with solution.
A capacitor "C", an inductor "L" and a switch "S" are connected in series. When the switch is open, the plate to the left of the capacitor has charge "Qo". The switch is closed the load and current vary sinusoidally with time. Represent graphically the load "Qo" and the intensity of current "I" as a function of time "t", and explain why the current leads the load by a phase difference of 90°.
Required information Problem 06.037 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS The current through a 17-mH inductor is 4 sin 100t A. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Problem 06.037.a - Voltage across an inductor Find the voltage vt). The voltage is cos 100t V.
Shown in the figure below is an "RLC" circuit driven by an AC power source. The AC power source has an RMS voltage of Vps(RMS) = 9.35 Volts and is running at a frequency of f = 113000 Hz. The resistor has a resistance of R = 1980 , the capacitor has a capacitance of C = 1.08e-09 Farads, and the inductor has an inductance of L = 3.71e-03 Henries. mm Vps Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit øztot Determine the numerical value of Ztot = 2384 Determine the numerical value of @Z tot Determine the current through the circuit: ● R www I(PEAK) = I(RMS) = ● ● Determine the voltage across the inductor: • VL(PEAK) = Volts Volts VL(RMS) = Amps Amps Determine the voltage across the capacitor: Vc(PEAK) = Volts Volts Vc(RMS) = = 33.85 a capacitive switcher Ω degrees C If a second circuit were connected in parallel with the resistor, this circuit would be considered as: O a high-pass filter a radio tuner O…
Given a capacitive load absorbing 5 kW with a power factor of 0.85. The source connected to this load is an AC voltage supply with 120V RMS at a frequency of 50 Hz. Please find; A) Peak current (m) and RMS Current (ms) Values B) Draw peak voltage and current phasors on phasor diagram with everything labelled C) Find the value of an inductor that when connected in parallel will improve the power factor to 0.95.
A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt. - omega for source in rad/s? - omegaR for circuit? -XL? -XC? -phi in radians? -Z? -imax?