What is the result of the following FAL instruction? Input L1 food А A HE О с. Ladder logic program FAL- FILE ARITH/LOGICAL Control Length Position Mode Destination Expression None of the choices (EN) (DN) Incremental (ER) #N7:101 R6:2 6 0 0 N7:100 On successive transitions, data will be copied from N7:100 into the next position in the file #N7:101 until N7:106 is reached O b. Once input A becomes true, data will be copied #N7:101 into the next address of N7:100 Od. On successive transitions, data will be copied #N7:101 into the next address of N7:100 Once input A becomes true, data will be copied six times from #N7:100 into the word #N7:101

What is the result of the following FAL instruction? Input L1 food А A HE О с. Ladder logic program FAL- FILE ARITH/LOGICAL Control Length Position Mode Destination Expression None of the choices (EN) (DN) Incremental (ER) #N7:101 R6:2 6 0 0 N7:100 On successive transitions, data will be copied from N7:100 into the next position in the file #N7:101 until N7:106 is reached O b. Once input A becomes true, data will be copied #N7:101 into the next address of N7:100 Od. On successive transitions, data will be copied #N7:101 into the next address of N7:100 Once input A becomes true, data will be copied six times from #N7:100 into the word #N7:101

Name: What is the result of the following FAL instruction?InputL1Looa.O b.O
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: What is the result of the following FAL instruction?InputL1Looa.O b.O C.AHEe.Ladder logic programFALFILE ARITH/LOGICALControlLengthPositionModeDestinationExpressionNone of the choices(EN)(DN)Incremental (ER)#N7:101R6:2600N7:100On successive transiti

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

B4
Refer to the following registers values and memory snippet to answer the following questions. DS=C224,, SS=D816,, SI=2340, SP=206C, Physical address Content C458A A5 DB 47 52 68 C9 C4590 FF A7 D8 11 C4594 39 C4 C4596 F6 1- what will be the value of AX after executing the following set of instructions? Execute the instructions dependently one after another. MOU AX, CSI +ØFH ] NOT AX MOU BL, I02354H ] ADD AL, BL AAA AX = 2- What is the physical address of the TOP OF STACK (TOS)? TOS =
Choose the instruction that will clear (makes zero) the contents of CX register. Assume that CX has 085AH. O a. NOT CX O b. AND CX,CX О с. ХOR CX,СХ O d. OR CX,CX
Multiplexer Logic circuit
Write the Verilog code for an 8-to-1 multiplexer using the if-else statement
1. In the following diagram, you have the architecture of the Intel 8086 questions: Briefly following microprocessor. [CO1/UNDERSTAND] To memory and Input/ Output answer the BIU 6. 5. 4 3. 2 Σ 6-Byte pre-fetch PA Seg X 10H + offset CS SS DS ES IP queue Control Unit EU AH AL AX General BH BL -BX -CX -DX Purpose Registers CH CL DH ALU DL SP ВР SI DI Operands Flags Block Diagram of 8086 Microprocessor Electronics Desk a)Why is the architecture of 8086 divided into two parts? How can the two units enhance the total system performance? b)How many registers are there inside Intel 8086? What is the purpose of segment registers and general-purpose registers? Mention the names also.
#12
Q.The outputs of four registers, A, B, C, D, H, L are connected through 8:1 line multiplexer to the input of a fifth register. X. Each register is 16 bits long. The required transfers are dictated by four timing variables. To through T3 as follows: TO: X-A T1: X-B T2 : X-C T3: X-D The timing variables are mutually exclusive, which means that only one variable is equal to 1 at any given time, while the others are equal to 0. Draw a block diagram showing the hardware implementation of the register transfers. Include the connections necessary from the four timing variables to the selection inputs of the multiplexers and to the load input of register X.
How many bits can the shift register save ? O a. 3 O b. 1 Oc.4 O d. 2
True or False Question
CONSTRUCT USING LOGIC GATES
After executing XLAT instruction, the content of system registers is: ES=4E25, DS=041C DI=6814, BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physical addresses). What is the content of AL before executing this instruction? H. H. Address 20н 40 H 60 н 80 H A0H СОн E0 H Content 447C 447D 447E 447F 4480 4481 4482 Notes: 1- Use the memory fragment shown to answer this question. 2- Write down the final value of AL as two hexadecimal digits without any additional characters.