Q. 3 For the following 4-bit shift register draw complete the timing diagram if theinput (Data_in) is 1101.Data_inq3Dq2q1Dobclkckclkckresetresetresetresetclkresetclk90q192q3D.

Answered: Image /qna-images/answer/ebfe9637-9516-4e3f-b536-a390125f4b62.jpg

Q. 3 For the following 4-bit shift register draw complete the timing diagram if the input (Data_in) is 1101. Data_in. q3 D Q q2 D q1 qo clk ck clk reset clk reset reset reset clk reset clk 90 q1 92 q3

Q. 3 For the following 4-bit shift register draw complete the timing diagram if the input (Data_in) is 1101. Data_in. q3 D Q q2 D q1 qo clk ck clk reset clk reset reset reset clk reset clk 90 q1 92 q3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve i) ii) and iii) only Show all the details with clear explanation
Design a combinational circuit that takes 3-bit pattern as input and outputs binary code of bit position of the first 1' in the pattern reading from MSB (2nd position) to LSB (0th position).An additional output variable V is required along with binary code to indicate that the binary code is valid or note i.e., if the input pattern is '000' then the output V should be '0' to indicate that the binary code is not indicating the bit position of first 1' and we don't care about the binary code if V = 0. Design the required circuit using dual 4x1 MUXS and minimum additional logic.Available resources along with dual 4x1 MUXS are NOT gates, 2-input(AND, OR, NAND, NOR) gates.
Develop the Q output waveforms for a 74HC190 up/down counter with the input waveforms shown in figure below. A binary 0 is on the data inputs. Start with a count of 0000. CLK CTEN LOAD
III) Convert from Hexadecimal to Decimal (a) 1ACED716 (b) C1AC18A.E8B916 IV) Convert Decimal to Hexadecimal (a) 114510 (b) 3176.5410
What is the value of the 8 digital bits that are represented as in the figure above if (Hint: the first bit is 1): a. The signal is encoded as NRZ-L: b. The signal is encoded as NRZ-I:
(b) Consider a voice signal from a analog telephone which needs to be digitized. Explain the steps involved in the conversion of analog to digital signal. If suppose the sampled analog values are 1V, 2V, 3.5V and 4.5V, use a 2 bit quantizer to digitize these values. Assume the range of sampled analog values from 0V to 5V. Provide the digitized values of this signal and draw the digital signal.
Q2: A 4-bit shift register with the feedback con ctions [4.3.2.1) and the initial condition (1,0,0.1) . (a) Draw the block diagram . (2) Find the generated PN code. ( 3 ) Draw the autocorrelation function of the sequence
Q2: Design 4-bit Parallel-in to Parallel-out (PIPO) shift register using RS - F / F . Draw the parallel output waveform for the parallel inputs [1100, 0101, 0001, 1010, 0111]. Then draw the state diagram.
Q2: Design 4-bit Parallel-in to Parallel-out (PIPO) shift register using RS-F/F. Draw the parallel output waveform for the parallel inputs [1100, 0101, 0001, 1010, 0111]. Then draw the state diagram.
1. Consider the CRC generator shown below. Determine the output of the CRC circuit (i.e. Q4 Q3 Q2 Q1 Q0, expressed as a decimal number) for the input sequence "1010" (input one bit at a time, left to right). Assume the CRC circuit is initialized to state 11111. D Q0 Q2 Q4 Q1 Q3 Clock - Data In
Q1: Design and draw time diagram of MOD-10 asynchronous/down counter that counts as 0000 to1001 knowing that Clock type is Negative and Output is taken from Q? Q2: Design and draw time diagram of asynchronous/UP counter that counts as 0001 tol001 knowing that Clock type is Negative and Output is taken from Q? Q3: Design 4- bit UP/DOWN Ripple Counter using j-k Flip-Flop
Binary 4-bit Asynchronous down Counter and explain how it functions, find real life applications