solve control systems pole placement 02Pole Placement.Plant20 PointsConsider the control system shown in figure.CompensationR(s)1G,(s)=s(s²+4s+5)and Ge(s) = (Kas+ K₂+)Q(x)G₂ (8)Design the given compensator to place the closed-loop poles at -5 and -51j6. Name all the factors.Y(s)

Approach to solving the question:

Answered: 02 Pole Placement. Plant 20 Points…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

9| Design Dc Dc converterto produced -15 V out put Prom Source Varies from 12 to 18 V. The load Resistance 15r.
Which of the following sensors has a permanent magnet inside? Hall effect sensor thru-beam optical sensor piezo-electric sensor LVDT capacitive proximity sensor |o|0|0|6
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
I need the answer as soon as possible
Do calculation. This is not a simulation problem
Explain the concept of power factor correction using a capacitor. List any two benefits of power factor correction.
Exercise Design a buck converter to produce an output voltage of 18 V across resistor. The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the RMS current in the inductor and capacitor. Assume ideal components. Assume the inductor be 25 percent larger than the minimum to ensure that inductor current is continuous.
A step-down chopper is to be used to supply power from a 600-V overhead wire to the commutator motor on a trolley bus. The motor may be mod- eled as a generated direct voltage in series with a resistance of 0.2 and an inductance of 25 mH. The frequency of the chopper is set at 500 Hz. (a) When the bus is stopped, what should be the ON time of the chopper to provide a motor current of 150 A? (b) What is the maximum possible generated voltage of the motor for which a current of 150 A can be supplied? (c) What is the average value of the supply current for the conditions of (a) and (b)? បទៅនឹងរស់របស (d) If the motor current is to be continuous, what should be its minimum. value?
In the common mode, ..... ..... ..... Select one: a. the output signal are in-phase b. an identical signal appears on both the inputs c. the outputs are connected together d. both inputs are grounded
4- Design a boost converter that will have an output of 60 V from a 24-V source. Design for continuous inductor current and an output ripple voltage of less than one percent. The load is a resistance of 50 2. Assume ideal components for this design. VL ooooo ip - ^
A three-phase bridge rectifier of Figure below has a purely resistive load of R 40 2 and is supplied from a 280-V, 60-Hz source. The b primary and secondary of the input transformer are a Primary + b Secondary ic Van in D₁D3 D5 D4D6D₂ 0₂ connected in Y. Determine the average output voltage of the rectifier if the source inductances are negligible.
Q2: Design a boost converter to provide an output of 18 V from a 12-V source. The load is 20 W. The output voltage ripple must be less than 0.5% and inductor current ripple less than 30%. The switching frequency is 25 kHz. Specify the duty ratio, the inductor size, and the capacitor size Assume ideal components.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning