A three-phase bridgerectifier of Figure belowhas a purely resistive loadof R 40 2 and issupplied from a 280-V,60-Hz source. The bprimary and secondary ofthe input transformer areaPrimary+bSecondaryicVaninD₁D3 D5D4D6D₂0₂connected in Y. Determine the average output voltage of the rectifier if the sourceinductances are negligible.

Given data Load value of the resistance; R=40 Ω RMS Supply voltage; Vs, RMS=280 V Supply frequency;…

A three-phase bridge rectifier of Figure below has a purely resistive load of R = 40 2 and is supplied from a 280-V, 60-Hz Primary in Secondary ic ASH D₁ D₂ D₂ www source. The b primary and secondary of the input transformer are connected in Y. Determine the average output voltage of the rectifier if the source nductances are negligible. D₂D6D₂

A three-phase bridge rectifier of Figure below has a purely resistive load of R = 40 2 and is supplied from a 280-V, 60-Hz Primary in Secondary ic ASH D₁ D₂ D₂ www source. The b primary and secondary of the input transformer are connected in Y. Determine the average output voltage of the rectifier if the source nductances are negligible. D₂D6D₂

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

N H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of tr 150usec and the source voltage Vs = 200V at frequency = 5 kHz. Calculate the average output voltage. IC L.C. the HoNo locor
In the following circuit, Vin is a sinusoid AC input voltage which has a 5. peak voltage of 15v. Zener diode D has a Zener voltage of 10V. Sketch the waveform of Vout. Hint: Consider when Zener diode is forward and reverse biased. R 1ka Vin Vout
Please answer fast to get a like
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
2. The rms value of the primary voltage, Vpri of a transformer with centre tapping in Figure 2 is 320/12 V. The turns ratio Nori: Nee is 10. Assuming ideal diodes, sketch the output voltage, Vo 3. Nr Ne D₁ K KH D₂ Figure 2 V, ~ VR R V₂=SV Figure 3 By assuming ideal zener diode, sketch the voltage across R, VR for the circuit in Figure 3 (V, 10 sin oot V). = FS markel
4) For single-phase half-controlled bridge rectifier shown in the figure : 1. Derive a formula for mean load voltage. 2. Draw the waveforms of Vosis w i3, ių and io assuming highly inductive Load and <=45°. T, 12
PROBLEM SET 1. Derive the formula for the RMS value for the following a) b) 3m 2. Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave. 3. Following the analysis applied to the half-wave rectifier with capacitor filter, show how to arrive at the output waveform for a center-tapped full-wave with filter capacitor. See output waveform on page 90. 4. Given: Half-wave rectifier; transformer secondary voltage = 32 V; Capacitance 4700 µF; average load voltage 18 V. Determine ripple factor and average load current 5. Design a half-wave rectifier with a capacitor filter that will deliver to the load an average voltage is 15 V at 280 mA. Ripple should not be higher than 5%. 6. Given: The input to a voltage regulator circuit varies from 11.4 to 12.2 V. The load voltage is to be maintained at 9.1V with maximum…
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
(b) Discuss the impact of connecting a large capacitor filter across the load in Figure Q1(ii). Use appropriate waveform sketch to aid your discussion. + Vp - Us R2 RL Vs ( (i) (ii) Figure Q1. Single phase half bridge rectifier: (i) with a Thyristor (ii) with a Diode
Quiq
Q5. For the following center tapped transformer, show the wave form across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 R 10 ΚΩ I14001 Q6. Can we operate normal PN junction diode in breakdown region for longer duration? Give reason Q7. What is the specialty of Zener diode so as we can operate it in breakdown region for longer duration? Q8. What is the difference between Zener breakdown and Avalanche breakdown? Q9. Draw Zener regulator circuit to obtain regulated DC voltage 6.8 V. Considering input DC voltage in the range from 10V to 30V. Consider load resistance of 10KS. Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load resistance is 2KN and input varies from 10V to 30V. Zener voltage is 5 V. Q11. What is LED? Q12. Which materials are used in manufacturing of LEDS?…
Q2) For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KO resistor) and the load current (through the load 2.2 KN resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode D1). The input Vi is sinusoidal with maximum amplitude (peak) of 14.1422 V and frequency of 60 Hz. The diode D1 is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi