An overhead line conductor having a parabolic configuration weighs 1.925 kg/m of length. The cross sectio area of the conductor is 2 cm² and the ultimate strength is 8000 kg/cm². The towers are 300 m apart havin difference levels of 15 m. Calculate the sag from the taller tower, so that the factor of safety shall be 5. Assum that ice load is 1 kg/m run and there is no wind pressure.

An overhead line conductor having a parabolic configuration weighs 1.925 kg/m of length. The cross sectio area of the conductor is 2 cm² and the ultimate strength is 8000 kg/cm². The towers are 300 m apart havin difference levels of 15 m. Calculate the sag from the taller tower, so that the factor of safety shall be 5. Assum that ice load is 1 kg/m run and there is no wind pressure.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.51P

See similar textbooks

Similar questions

Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
Help me i need answer in 30 minutes please please please please In a 10 km long three phase conductor diameter of 2.5 mm the conductors are arranged symmetrically with a spacing of 2 m. So find per phase inductance.
Draw three transformers for each of the different three-phase connections. That is, draw three transformers and then make the connection, eg star-star, then redraw three transformers and make another three-phase connection, and so on until all four combinations of three-phase connections are made.
15) Kirchhoff's Voltage Law (KVL) states that A) the product of the phasor voltages around any closed path must equal zero. B) the sum of the phasor voltages around any closed path does not have to equal zero. C) the sum of the phasor voltages around any closed path must equal zero. D) the sum of the phasor voltages around a closed path cannot include "through the air."
A 34.5 KV feeder line is 5 mi long. The conductors are spaced 4 ft horizontally. The conductor is 4/0 copper with GMR of 0.01688 ft. What is the reactance?
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
Determine the short-circuit current ISC3,0.4kV for a 3-phase short- circuit fault at F. Give your answer up to 2 decimal in kA but do not enter the unit in your answer. Transformer T1 Transformer T2 Cable C1 Isc3,6.6kV Isc3.0.4kV O + j0.150 F 1 MVA 2 MVA 22/6.6kV 25 MVA fault level 6.6 kV/400V Z=3% 6.6 kV switchboard 400 V switchboard
EHV lines often have more than one conductor per phase; these conductors are called a _________.
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
For the system shown in Figure 3.34. draw an impedance diagram in per unit by choosing 100 kVA to be the base kVA and 2400 V as the base voltage for the generators.
Calculate the inductance of the single-phase double circuit line shown in the figure, the diameter of each conductor is .2 cm d=2 cm 100 cm 100 cm-
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence