6.21. For a 3-phase half-wave diode rectifier, derive an expression for the average output voltage Vo in terms of maximum value of source voltage from line to neutral. If this rectifier feeds RL load with R = 5 2 and L = 3 mH, find the average load current for 3-phase input voltage of 400 V, 50 Hz. jent galley Jaq gets odd rot [Ans. 54.011 A] منسمة

6.21. For a 3-phase half-wave diode rectifier, derive an expression for the average output voltage Vo in terms of maximum value of source voltage from line to neutral. If this rectifier feeds RL load with R = 5 2 and L = 3 mH, find the average load current for 3-phase input voltage of 400 V, 50 Hz. jent galley Jaq gets odd rot [Ans. 54.011 A] منسمة

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6.21. For a 3-phase half-wave diode rectifier, derive an expression for the average output voltage Vo in terms of maximum value of source voltage from line to neutral. If this rectifier feeds RL load with R = 5 2 and L = 3 mH, find the average load current for 3-phase input voltage of 400 V, 50 Hz. jent galley Jaq gets odd rot [Ans. 54.011 A] منسمة
Answer and draw
A Full-wave bridge rectifier Circuit contains 4 Germanium diodes Cuse the Constant voltage drop model with VD = 0.30) driving ac a Load resistance of 10 kur. An Source with a Peak value of 4ou at bottz Vortage Source with a applied to the Circuit. a DIS 2 Determine the de value of the output wave form Determine the value of the Capacitor In uf needed to limit the output ripple vortage to 0.5 V if the Peak output voltage is equal to Upic -2VD
Please show all work
A half-wave recitifier is connected to a 50V AC source. If the load resistance is 100 ohms, find: 1) Max load voltage 2) Average load voltage 3) Max load current 4) Average load current 5) RMS load current 6) PIV rating for diode ...
Answr all the questions one by one and solve all the unknown values giving all the correct details Let the last digit of the ID = 9
a) Use the diode’s characteristic equation,ID=Is exp(VD/VT), to determine the currentsourceIso that the output voltage is 1.5 V. b) If a load is attached to the output that draws 1 mA, what is the output voltage? c) If the circuit heats up to 40◦C, what is the output voltage without a load?
1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 For any of the diodes, describe with the aid of diagrams/illustrations its applications in an AC to DC Bridge rectifier power supply circuit. For your circuit show and describe how you are going to smooth out the ripple voltage that will be present.
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
A silicon diode has 1 ampere DC of current in biasd mode. What is voltage drop across the diode?
Zener diodes are special purpose diodes designed to operate in their breakdown regions. Describe the working principle and characteristics of a typical Zener diode found in the market place. The Zener-diode regulator circuit shown below is to be used to provide a stabilised output to the load. The zener diode characteristic is also shown. Find the load voltage and source current if the battery voltage is 20 V, series resistance is 1.4 kohm and load resistance is 6 kohm
5) The figure below illustrates a simple voltage threshold detection circuit. To understand how it operates, we will analyze its behavior based on the simple constant voltage drop model for both diodes. Assume the Zener diode (Z1) only conducts when its breakdown voltage of 10V is reached. Di is a red light emitting diode (LED). Assume it conducts after its forward bias voltage of 1.8V is reached. Vin is unknown. Assume Zj acts as a perfect Zener diode (without series resistance). What voltage does Vin have to reach before there is a current through R¡? What voltage must Vin reach before current flows through R2? Write an equation for the current through Zi in terms of Vin, Rị and R2 that is valid when Vin is high enough for both diodes to be conducting. a. b. c. R2 Vino R1 LED