A 50-Hz sinusoidal voltage of maximum value of 400 volt is applied to a series circuit of resistance 10 Ohms and inductance 0.1 Henry. Find an expression for the value of the current at any instant after the voltage is applied, assuming that voltage is zero at the instant of application. Calculate its value 0.02 second after switching on.(13 Marks)

A 50-Hz sinusoidal voltage of maximum value of 400 volt is applied to a series circuit of resistance 10 Ohms and inductance 0.1 Henry. Find an expression for the value of the current at any instant after the voltage is applied, assuming that voltage is zero at the instant of application. Calculate its value 0.02 second after switching on.(13 Marks)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

When a voltage of 100V at 50Hz is applied to a choking a coil A, the current taken is 8A and the power is 120W, when applied to a coil B, the current is 10A and the power is 120W. what power will be is 10A and the power is 120W. what power will be taken when 100V is applied to the two coils connected in series?
Pls. write solution neatly
The meter constant of a single phase 230 V induction watt hour meter is 400 rev/kWh. The speed of the meter disc for a current of 10 A of 0.9 pf lagging will be ?
Determine the CH2 peak value. Write the values only in four decimal places. the correct answer is 1.9600 please show the solution thank you!
Question 4 a) B M Figure 4 Figure 4 shows the graph of the ripple current. Answer the following i. Describe the function of A. ii. iii. Describe the function of B. Identify the ideal paramater to get the good power supply.
When a voltage of 100 volts at 50 Hz is applied to a series connection of a resistor Aand an inductor A, the current taken is 8 A and the power is 120 watts. When appliedto another series connection of a resistor B and an inductor B, the current is 10 A andthe power is 500 watts. What current and power will be taken when 100 V is appliedto the two coils in series?
Three types of electric devices A, B, and C are connected in series across a 115-volt ac source, and the voltage drops across the individual units are equal. If EB leads EA by 90 elec deg and EC lags behind EA by 90 elec deg, what are the emfs across A, B, and C?
Hi, I need a correct answer for this assignment question Thanks
3. The figure on the left below shows a schematic diagram of a battery. The voltage measured by U1 is called the terminal voltage given R1 = 1 ohm. In the figure on the right below, the terminal voltage of each of the battery-resistor combination is Vr = 1.5 volts. Find the following: a. The current passing through R5. b. The currents passing through R1 and R3 C. The voltage across R1. d. The voltage of the battery EMF. e. The percentage of voltage loss ot the battery due to the internal resistance R1. The power dissipated by the internal resistance R1. g. The power dissipated by R5 if R1 = R2 = R3 = R4 = 0. h. The percentage of power dissipation loss due to the four resistors R1, R2, R3, and R4 f. R1 R3 S10 R1 U1 1.500 EMF EMF R5 100 V1 R2 $10 EMF R4 EMF EMF
A direct current of 12.5 A flows in a 25-ohm resistance. Determine the maximum value of an alternating current that will produce heat at the same rate in this resistance. Expresss answer to the nearest hundredths.
Determine the DC currents (IB, Ic and lĘ) and dc junction voltages (VBE, VCE and VCB) Ig=Blank 1 mA, Ic=Blank 2 mA, IĘ=Blank 3 mA, VBE= Blank 4 V, VCE = Blank 5 V and VCB = Blank 6 V Use 2 decimal places. Use the following values: VBB = 2V RB = 7 kQ Rc = 248 Q Vcc = 19 V BDc = 56 Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer Blank 4 Add your answer Blank 5 Add your answer Blank 6 Add your answer
three type of electric device A, B, and C are connected in series across a 115 volt AC source, and the voltage drops across the individual units are equal. if EB leads EA by 90 elec deg and EC lags behind EA by 90 elec deg, what are the emfs across A, B, and C?