A generation station of 3 MW supply a two regions A & B .The linelosses are neglected and the load variation of these regions is as follow:Region A(Time)11 a.mFrom11 a.m to6 p.mNo-loadFrommidnight toFrom5 a.m toFrom8 a.m toLoad (kw)5 a.mNo-load8 a.m1200800Region B(Time)FromFrommidnight to6 a.m to3 p.m to7 p.m to6 a.m3 p.m7p.m9 p.mLoad (kw)400900No-load1800FromFromFrom6 p.m tomidnight600From9 p.m tomidnight2001-Plot The daily load curve of the total system.2-Find the load factor, diversity factor,plant user factor and the actualgeneration by the station in kwh in the day for the total system.

Step 1: Given load profile of a 3MW =3000 kW capacity generating station. But the time divisions are…

Answered: A generation station of 3 MW supply a…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
4) Therenin's Equinlena Circuit and Marimum Poer truns fer Thiorem a) For the Circuit derive the given in the figure, therenin's eq uivalence Circuit acrass the branch witn the loud impedanu. b) Culculate to deliver the volue of the load Impedanca makimum power to the load, c) caleula te the Power dissipa ted through the loud, 72
A 50 Hz high voltage Schering bridge is shown in the figure. The component parameters are as follows under balanced condition: Cs-150 microfarad, C2-0.677 microfarad, R2-634 ohm, and R1-168 ohm. Find the dissipation factor of the tested material. 220V rms Lütfen birini seçin 0.1340 b.0.1672 E0051 0.0.0749 e.0.1128 88888888 00000000 25 kV rms R R₁ R₂ II (C₂ 12²
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
what are load values in this power flow system
Show the solution Using 24v AC source design a 24v unregulated power supply circuit that will power a 1kohms load with 50mv ripple. Draw your designed unregulated power supply circuit
Two impedances, Z1 = 2+j6 N and Z2 = 6-j12 N are connected in series with a 220-V 60-Hz supply. At what frequency will the circuit act as a purely resistive load? O 84.85 Hz O 116.62 Hz O 82.46 Hz O 120 Hz
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
The temperature of a noninductive heater unit is controlled by a reactor. The heater unit and the reactor are connected in series across a 250 V, 60 Hz source. The voltage across the heater unit is 200 V. The voltage across the reactor is 100 V. The current in the circuit is 10 A. Determine: the power factor of the series circuit. the power factor of the reactor. the impedance of the reactor. the effective resistance of the reactor. the inductive reactance of the reactor
two generators supplying a load. Generator I has a no-load frequency of 62.5 Hz and a slope Sp1 of I MW/Hz. Generator 2 has a no-load frequency of 62.0 Hz and a slope sp2 of I MW/Hz. The two generators are supplying a real load totaling 2.5 MW at 0.8 PF lagging. (a) At what frequency is this system operating, and how much power is supplied by each of the two generators? (b) Suppose an additional I-MW load were attached to this power system. What would the new system frequency be, and how much power would Gl and G2 supply now? Generator 1 VT V2 Generator 2 VTí KVAR KVAR

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning