2. For the 60 Hz load, the RMS voltmeter measures 120 V. The phasor diagram for the power is also shown. Find the following: a. The complex power. S =? b. The apparent power. |S| = ? c. The power factor. pf = ? d. The power factor is leading or lagging? Consider Vs = 120V and w = 377 rad/sec V=120-V S 00:= 377. rad sec -100 -200+ Im (VA) 100 A 200 WM Load 300 Real VA(W)

2. For the 60 Hz load, the RMS voltmeter measures 120 V. The phasor diagram for the power is also shown. Find the following: a. The complex power. S =? b. The apparent power. |S| = ? c. The power factor. pf = ? d. The power factor is leading or lagging? Consider Vs = 120V and w = 377 rad/sec V=120-V S 00:= 377. rad sec -100 -200+ Im (VA) 100 A 200 WM Load 300 Real VA(W)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
The average value of a double-frequency sinusoid, sin2(t+), is given by (a) 1 (b) (c) Zero
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
Find the RMS value..
Suppose I have two peak phasor voltages, V, = 100245° and V, = 75Z-60°. Circle Your Choices: I. The frequencies associated with the phasors are (0 Hz, 60 Hz, 50 Hz, Unknown). II. The rms value of the first phasor is (100, 70.7, 141, 200) volts. III. If you want to add these two phasors, the frequencies must be (60 Hz, 50 Hz, The same, Integer multiples of a given frequency.)
A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load impedance.
Quistion.4. a) A sinusoidal voltage is applied to the resistive circuit in figure.Q.4. a. Determine the following: i. Ims ii. Iavg iii. Ip iv. Ipp 10V 1.0 ΚΩ Figure.Q.4.a
Two ac generators supply the same voltage. However, the first generator has a frequency of 1.2 kHz, and the second has a frequency of 5.7 kHz. When an inductor is connected across the terminals of the first generator, the current delivered is 0.15 A. How much current is delivered when this inductor is connected across the terminals of the second generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. Number i Units 1₂ L 0000 V sin 2π f₁t Circuit 1 12 L 0000 Vo sin 2x f₂t Circuit 2
choose the correct option for ac circuit
P.4: Find the rms value for the following sinusoidal waveforms a. v = 20 sin 754t b. v = 7.07 sin 377t c. i = 0.006 sin(400t + 20°) d. i 16 x 10-3 sin(377t - 10°)
C. Draw a general sine wave V vs t and I vs t plot for a purely resistive and a purely inductive circuit and show leading lagging parameters and clearly mark the phase difference.