I need an expert. I previously sent a request, and the expert divided the time periods equally for both areas A and B. I did not understand how and why this was done. Please explain to me with a diagram why we do this. A generation station of 3 MW supply a two regions A & B .The line losses are neglected and the load variation of these regions is as follow: Region A (Time) 11 a.m From midnight to From 5 am to From 8 a.m to From 11 a.m to Load (kw) Region B (Time) 5 a.m No-load 8 a.m 1200 800 6 p.m No-load From From From midnight to 6 a.m to 3 p.m to 7 p.m to 6 a.m 3 p.m 7 p.m Load (kw) 400 900 No-load 9 p.m 1800 From From 6 p.m to midnight 600 From 9 p.m to midnight 200 1-Plot The daily load curve of the total system.

I need an expert. I previously sent a request, and the expert divided the time periods equally for both areas A and B. I did not understand how and why this was done. Please explain to me with a diagram why we do this. A generation station of 3 MW supply a two regions A & B .The line losses are neglected and the load variation of these regions is as follow: Region A (Time) 11 a.m From midnight to From 5 am to From 8 a.m to From 11 a.m to Load (kw) Region B (Time) 5 a.m No-load 8 a.m 1200 800 6 p.m No-load From From From midnight to 6 a.m to 3 p.m to 7 p.m to 6 a.m 3 p.m 7 p.m Load (kw) 400 900 No-load 9 p.m 1800 From From 6 p.m to midnight 600 From 9 p.m to midnight 200 1-Plot The daily load curve of the total system.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Similar questions

Where did it come from?
Consider the switching waveforms shown below, operating with a duty-cycle of 30%. Which statements correctly describe the switching circuit, load and circuit operation? (Multiple answers possible, but wrong answers will deduct marks) Voltage across load Voltage (V) 000 120 0000 100 80 60 40 20 30 Time (us) The load must be predominantly resistive. The average current in the load is 1.0A. The RMS current in the load is approximately 1.414A. The load must be predominantly inductive. The resistive part of the load is 200ohms. The average current in the load is 0.6A. O The resistive part of the load is 50ohms. 0 0 10 20 40 50 60 Current (A) 2 5 0.5 0 0 10 Current through load 20 W 30 Time (us) 40 50 60
A generating station is to supply four regions of load whose peak loads are10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Then the installed capacity is (25 to26)MW. O (24 to25)MW. O (23 to24)MW. O
Why the tranformer rattigs are mentioned in KVA. Discuss in brief.
What will be the value of the twiddle factor: W42
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
Three generators are rated as follows: G1: 100MVA, 33kV, xg1 = 0.1pu G2: 150MVA, 32kV, xg2 = 0.08pu G3: 110MVA, 30kV, xg3 = 0.12pu. Determine the reactance of the generator corresponding to base values of 200MVA and 35kV
Explain the principles of power quality in electrical systems and the factors affecting it, including harmonics and voltage sags.
a) A sinewave is having a frequency of 100 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.8 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and o =30 degrees. Vp t= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.8 ms b) Angular frequency =
1. Sinewave A lags sinewave B by 30°. Both have peak values of 15V. Sinewave A is the reference with a positive going crossing at 0°. Determine the instantaneous value of sinewave B at 30°, 45⁰, and 200⁰.