The peak amplitude of the sinusoidal voltage source in the circuit shown in (Figure 1) is 150√2 Vand its period is 200 μs. The load resistor can be varied from 0 to 20 2 and the load inductorcan be varied from 1 to 8 mHPart ACalculate the average power delivered to the load when R = 10 and Lo = 6 mHExpress your answer to three significant figures and include the appropriate units.P = 9.00 WFigure300 Ωw1μFRo1 of 1SubmitPrevious AnswersCorrectDetermine the settings of R, and Lo that will result in the most average power being transferred to RoPart BFind RoExpress your answer to three significant figures and include the appropriate units.НА?Ro=ValueUnitsSubmitRequest AnswerPart CFind LoExpress your answer to three significant figures and include the appropriate units.HA?Lo=ValueUnitsSubmitRequest Answer

To solve the problem, we need to determine the optimal values for R0 (the load resistance) and L0…

Answered: The peak amplitude of the sinusoidal…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter7: Alternating Current, Power Distribution, And Voltage Systems

Section: Chapter Questions

Problem 7RQ

See similar textbooks

Similar questions

See images attached. Help with finding sinusoid equations for graph
The sinusoidal current waveform having the R.M.S value of 20 A, then the maximum value is Answer and unit
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
The rms value of the resultant current in a wire carries a dc current of 10 A and a sinusoidal alternating current of peak of value 20 A is-
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz
The source in the circuit shown is a sinusoidal source. The supply voltages across various elements are marked in the figure. The input voltage is: 3V- ww -14 V-10V moon It
An alternating current has the frequency of 62 Hz, then the value of angular velocity is The peak to peak distance of a sinusoidal waveform displayed on a C.R.O. screen is 9 cm and the 'volts/cm' switch is on 21 V/cm. The peak voltage is given by 133.62 V O 94.50 V O 2.33 V 189.00 V
When a capacitor is discharged through a resistor, the discharge curve is exponential Sinusoidal Step Square
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
An alternating current has an rms value of 50A and a frequency of 60HZ.Find the time taken to reach 50A for the first time.
Problem 3 Compute the average and rms voltage of the waveform shown in the figure below. 6V - t 4 ms 4 ms 4 ms 4 ms -3 V

SEE MORE QUESTIONS

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning