6)- The diameter of a copper conductor varies over its length as shown in giventable. Calculate the average precision.Reading No.1Diameter (mm)2.2822.1232.2642.2952.1162.14

The question shows a table where the diameter of a copper conductor is measured across six readings.…

Answered: 6)- The diameter of a copper conductor…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 14RQ

See similar textbooks

Similar questions

25 PROBLEMS 12 cm +1.5-mm gap IP1000t Armature (sheet steel) Cast steel A = 2 cm? throughout FIGURE 1.27. The relay shown in Figure 1.27 has a core made of cast steel and an armature of sheet steel. A flux of 0.8 T in the air gap produces a force that pulls in the CO armature. a. Determine the required current to pull in the armature. b. What force is exerted on the armature to overcome the spring tension? c. Assuming in the closed position the air gap is reduced to 0.1 mm, to what value may the current be reduced (dropout current of relay) just to retain closure? Assume that the same force is required in the closed position to overcome the spring force.
22
Figure Q1(a) shows a piece of ferromagnetic core with magnetic flux (B) with circular current (I) around the core. Figure Q1(b) show laminated ferromagnetic core with the same magnetic flux (B) and circular currents. With the aid of diagrams, explain how the current as highlighted in red (I) is developed in the ferromagnetic core in Figure Q1(a). B (a) (b) Figure 1(a) A ferromagnetic core and (b) laminated ferromagnetic core
one turn of a copper bar is produced by cutting copper washer along a radius and spreading the ends. The washer is cut from soft drawn copper having a resistivity at 20 degrees celsiu of 1.732 micro ohm-cm. The washer is 0.125 inch thich and has inside diameter and outside dianmeter of 1 inch and 9 inches respectively. Calculate the exact resistance between the two end of the turn. Assume the contact along the ends of the turn to be perfect over the entire crown section.
Ferromagnetic materials have this characteristic. A. A relative permeability slightly less than one. B. A relative permeability slightly greater than one. C. A very high resistivity. D. A high relative permeability.
The number of disc insulators used in a suspension insulator setup with string efficiency 80 %, phase voltage 33 kV, and the voltage across insulator nearest to conductor 11 kV is .......................... Complete the answer.
I need the answer as soon as possible
An aluminum wire has a diameter of 2 mm. What must be the diameter of copper wire of the same resistance and length as aluminum? A. 1.33 mm B. 1.45 mm C. 1.56 mm D. 1.75 mm
Which of the following is not true for ferromagnetic materials? Please choose one: a. High?mthey have value. b.Above the Curie temperature, they lose their non-linear properties. C. a fixedµrthey have value. D.The energy loss is proportional to the area of the hysteresis loop.
Figure Q1(a) shows a piece of ferromagnetic core with magnetic flux (B) with circular current (I) around the core. Figure Q1(b) show laminated ferromagnetic core with the same magnetic flux (B) and circular currents. With the aid of diagrams, explain what happens to the current in Figure Q1(a) if the magnetic flux is always constant. (a) (b) Figure 1(a) A ferromagnetic core and (b) laminated ferromagnetic core
The property of insulating material which makes the breakdown voltage high in a cable is ...... Good Mechanical strength O High conductivity O High dielectric strength O High insulation resistance
State the main constituent elements of electrical cables, as well as the materials from which they may be made. Describe the following designations: H05VV-U 1G4 mm? and LSXAV 3x16 mm?.

SEE MORE QUESTIONS

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

6)- The diameter of a copper conductor varies over its length as shown in given table. Calculate the average precision. Reading No. 1 Diameter (mm) 2.28 2 2.12 3 2.26 4 2.29 5 2.11 6 2.14