Please find attached questions. B3.A cable connected to a 220V supply to electric heater which has ratecurrent is 33A. This PVC cable is laid in a PVC conduit. Assume theAmbient Temperature Factor is 0.97 and the length is 27m. For B-TypeMCCB, voltage drop can't be more than 4V.Find the following.a) MCCB ratingb) Rated current of Cablec) Cable Sizingd) Voltage Drop of the circuit

I hope you find this helpful. If you have any question or clarification, do not hesitate to reach…

Answered: B3. A cable connected to a 220V supply…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

Discuss causes of insulation failures in high voltage engineering. High voltage engineering
Full calculation with any assumption needed. All sub questions please as it is all related.
22. The voltage applied to the h.v. side of a trans- former during short-circuit test is 2% of its rated of voltage. The core loss will be........percent the rated core loss. (a) 4 (b) 0.4 (c) 0.25 (d) 0.04
Describe the functions of the transformer, capacitors and voltage regulator in power supply circuit.
In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 15kV and that across the next unit is 12kV. Estimate: ratio of mutual to self-capacitance i. the bus-bar voltage of the substation. Efficiency across the string of insulators ii. iii.
Consider Two same size Parallel connected PV modules,each with the specification as Po=100W, Voc= 24.5V and Isc=5A.then choose the correct Statement Refer to this connection. a. The output power and voltage from this panel is Po=50W,Voc= 24.5V b. The output power and voltagefrom this panel is Po=200W,Voc= 24.5V c. The output power and voltage from this panel is Po=200W,Voc= 49.0V d. The output power and voltage from this panel is Po=100W,Voc= 24.5V
Report:- 1. Plot (total core loss / cycle) as a function of frequency. 2. Evaluate (K & K2 )corresponding to value of (voltage & frequency). 3. Calculate hysteresis and eddy current losses at rated voltage and frequency.
Q1. Describe the following related to Current Transformer (CT): (i) Draw the equivalent circuit diagram of CT and develop the corresponding phasor diagram. Draw the transient response of CT and describe the transient errors in a CT. [5] [5] (ii)
Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer
Q.4/ choose true or false: 1. The reluctance of any core is proportional directly with the length of it and inversely with both the permeability and the cross-section area of it. 2. The number of parallel paths in wave windings is equal to twice of the number of poles. 3. In dc machines with same values of Z, N, Ø, the emf for wave winding type is more than emf of lab winding type. 4. If we insert a current in such a conductor subjected to a constant magnetic field, a movement will achieved giving the principle of electric generator.
??

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning