A) Write an 8086 program toto find the average of fivemarks stored in DTI. Thenstore the result in memorylocations starting with anoffset of 1200H.B) Write an 8086 program tofind the perimeter of fiverectangles whose lengthsare stored in DT1 andwidths stored in DT2. Thenstore the results in memorylocations starting with anoffset of 1100H.C)Write an 8086 program tofind the average of fivenumbers stored in ARR.Then store the result inmemory locations startingwith an offset of 1000H

A) Program to Find the Average of Five Marks Stored in DT1Objective:Input: Five marks stored in…

Answered: A) Write an 8086 program to to find the…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Solve in 8086 microprocessor
Task 2: Draw pinouts of 8088 or 8086 microprocessor (µp). Also draw schematics of 8088/8086 µp buses with Latch(s) [IC: 74LS373] and Buffer(s) [IC: 74LS245]. Write purpose of using latch and buffer ICs with up buses.
By using the information given in image below design a BCD Counter. You have to provide all the necessary information needed to design this circuit.
A) Write a program in 8086 microprocessors to find out the addition of two 8-bit BCD numbers, where numbers are stored from starting memory address 2000: 500 and store the result into memory address 2000: 600 and carry at 2000: 601. B) Write an 8086 program to sort an array of 8 elements in ascending order C)Write an 8086 program to sort an array of 8 elements in descending order.
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate the complete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform. (Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.) (Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.) 1/6 Pat DigClock Part List OFFTIME = SuS DSTM1 ONTIME = DELAY= STARTVAL = 0 OPPVAL = 1 Sus EUK FleStim AC Lbrajes Design Cache b) Read the specification of 74LS47 (BCD-to-7-Segment Decoder shown in Appendix) to see how the logic IC operates to drive a 7-segment LED display. Draw the circuit connection of the decade counter in (a) and the decoder to display the count value on the 7-segment LED display. Further explain why common anode…
Q34: Write an 8086 program to store the remainder of the division (Y-X/Z) to the memory location which has an offset address of 1414H. (Note: use X=73H and Z-OCH) Q35: Write an 8086-microprocessor program to find the sum of 25- byte numbers stored in memory locations starting at the offset address 3020H and store the result in memory location with offset address 3040H.
Include circuit diagram
Write an 8086-microprocessor program to store the number from (16 to OH) to memory locations starting at the ofsset address 4000H.
Q34: Write an 8086 program to store the remainder of the division (Y-X/Z) to the memory location which has an offset address of 1414H. (Note: use X=73H and Z=0CH) Q35: Write an 8086-microprocessor program to find the sum of 25- byte numbers stored in memory locations starting at the offset address 3020H and store the result in memory location with offset address 3040H.
Question 1 The static RAM 6264 is located starting at address 9E000 of the 8086 address space as shown in the figure below. a) What is the value of n? (see the notes below) b) Show the address decoding circuitry adding external logic gates if necessary. You can use the table below to analyze the address. • You must show all the connections to A, B, C, (G2A), (G2B), and G1. • The address lines connected to the 6264 are indicated by n and the data lines are indicated by d. You must also show the connection between the 74LS138 and the 6264 clearly on the figure below. 7415138 G2A GZB GI S Outputs n 1888 CE 6264 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 AO
1. Design 8086’s memory system consisting of 64K bytes of ROM using32KX8 chip. The memory is to reside over the address range 60000Hthrough 6FFFFH. Select suitable address maps.2. If the memory chip size is 1024 X 4 bits, how many chips are required tomakeup 2K bytes of memory?3. Interface 16 K word of memory to the 8086-microprocessor system.Available memory chips are 8 K X 8 RAM. Draw the memory table.
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate thecomplete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform.(Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.)(Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.)

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS