Q1) A nuclear power station has plant capacity Factor of 0.7 and supply a two region Ad efficiency of plant 40%. The line losses are neglected and the load demand according to the Total load curve below:- Power (MW) 4 170 160 150 140 130 120 110 100 60 50 882289 229 90 80 70 7 30 20 10 Time (h) 2 4 6 8 10 12 14 16 18 20 22 24 1-Plot the duration load curve. 2- Determine the maximum amount of fuel (u235) in could be consumed for one day.

Q1) A nuclear power station has plant capacity Factor of 0.7 and supply a two region Ad efficiency of plant 40%. The line losses are neglected and the load demand according to the Total load curve below:- Power (MW) 4 170 160 150 140 130 120 110 100 60 50 882289 229 90 80 70 7 30 20 10 Time (h) 2 4 6 8 10 12 14 16 18 20 22 24 1-Plot the duration load curve. 2- Determine the maximum amount of fuel (u235) in could be consumed for one day.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

2. a) Explain the terms load factor and diversity factor. b) Discuss the advantages of interconnected grid system. c) A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Calculate: (i) the maximum demand on the station, (ii) annual energy supplied by the station and (iii) suggest the installed capacity and the number of units.
Explain the concept of FACTS (Flexible Alternating Current Transmission Systems) devices. How do they enhance the control and stability of power systems? Provide examples of FACTS devices and their applications.
power system
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
Analyse several voltage and current situations in different loading scenarios in a simplified radial (transformer to consumption) medium-voltage power system example. There are only 2 nodes in the 35 kV line – node 0 from the 110/35 kV and node 1 with one consumer. Briefly reflect on the complexity of the calculations for known input or output voltage, as well as for fixed or voltage-dependent consumption in this simple power system model. Analyse and discuss the sensitivity of the voltage drop [in % of amplitude and the degrees of phase] with respect to the current level [in %] and to the power factor.
The impedance ZL in the circuit shown in Figure is adjusted for maximumaverage power transfer to itself.(a) What should be the value of ZL?(b) What is the maximum average power delivered to ZL?(c) What percentage of the average power delivered to the linear transformer is delivered to ZL?
Id is : 510221
A generating station has a maximum demand of 20 MW, a load factor of 60%, a plant capacity factor of 48% and a plant use factor of 80% Find: 1)the daily energy produced (2) the reserve capacity of the plant. (3) The maximum energy that could be produced daily if the plant was ruinining all the time.(4).Maximum energy that could be produced daily if the plant was running fully loaded and according to an operating schedule.
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
A synchronous generator of reactance. 1.3 p.u. is connected to an infinite bus bar through transformer and transmission line of reactance 0.2 p.u. and 0.5 p.u. respectively. The inertia constant, H = 4 MW-sec/MVA. The infinite bus having the voltage of 1 p.u. and excitation voltage is 1.2 p.u. The resistance and damping are negligible, system operates at a frequency of 50 Hz. Calculate the frequency of oscillation, if system is loaded to 40% of maximum limit?
A generation station of 3 MW supply a two region A & B .The load variation of these regions is as follow: Region A (Time) From midnight from 4a.m to From 10a.m to From 5p.m to to 4a.m 10a.m 5p.m 7p.m From 7p.m to midnight Load(kw) 800 500 NO load 300 100 Region B (Time) From From From From From midnight 6a.m to 2p.m to 4p.m to 9p.m to Load(kw) to 6a.m 300 2p.m 4p.m 9p.m midnight 600 No load 800 1100 With neglect transmission line losses. Find the load factor, diversity factor, reserve capacity,plant use factor.
I need the answer at 20 minute