Problem-1(Ch-4: FET Amplifier)A common-source amplifier circuit has following parameters: Kn=0.5 mA/V², VDD = 5 V,RD = 10 k2, R₁ = 160 k2, R2 = 40 kQ, Rsi = 5 k, VTN = 0.5 V, and λ = 0.01 V-1.(a) Determine the Q-point of the MOSFET.(b) Draw the small signal model of the given amplifier.(c) Determine the input and output resistance of the given amplifier.(d) Determine the small signal gain of the given amplifier.ViRsiww5=wwwwwVDDR₁R2wwRDvo

Answered: Problem-1 (Ch-4: FET Amplifier) A…

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 5R: From a cost standpoint, which system is more economical to install: a master amplifier distribution...

See similar textbooks

Similar questions

Coonsider the common emitter amplifier shown in figure below. Assume a β of 100, VBE = 0.7V, VT = 25mA and VA = 100V. Draw an equivalent DC model and determine the rπ, transconductance (gm) and ro. Draw an equaivalent AC model using the small-signal model Find an expression for vbe and vo in terms of the input voltage
Design a common-emitter amplifier to provide a small-signal voltage gain of approximately -10. 1. Consider the circuit shown in Figure 1. Show the following calculations in your notebook: Calculate a value for Rc so that A, z –10 Calculate values for R1 and R2 so that the circuit is bias stable and near the center of the load line. (Note: Use the datasheet for the 2N5209 transistor to make your calculations more accurate). Vcc = 10 V R1 Rc Cc2 Cci RL Vs R, REj = 499 Q Figure 1: Common-emitter amplifier for part #1
Provide the detailed explanation -
4. A certain common-emitter amplifier has a voltage gain of 100. If the emitter bypass capacitor is removed, (a) The circuit will become un stable (c) The voltage gain will increase (b) the voltage gain will decrease (d) the Q-point will shift 5. For a common-collector amplifier, RE =1002, r'e= 10 2, and Bac=150. The ac input resistance at the base is: (a) 1500 2 (b) 15 k2 (c) 110 Q (d) 16.5 k2 6. If a 10 mV signal is applied to the base of the emitter-follower circuit in Question 5, the output signal is approximately (a) 100 mV (b) 150 mV (c) 1.5 V (d) 10 mV
Q1. For the MOSFET circuit below, input is sinusoidal signal of amplitude IV and frequency 50Hz. Find, the DC operating point, Plot the frequency response and Plot the input, output and transfer characteristics and find out the small signal equivalent. Assume an overdrive voltage of 0.2V Use MOSFET 500nm Library file provided. F Vdd=5V -=80 K R1 (1 1.20F
Consider the amplifier shown. Assume that the transistor has the following small signal parameters: A gm : = 4 x 10-³ V² ro= 10 x 10³ a) Draw the small signal model. Assume that the frequency is high and model the capacitors as short circuits. b) Using the above small signal model, perform small signal analysis and determine a numerical value for Av. Show your work! Do not make approximations. c) Using the above small signal model, perform small signal analysis and determine a numerical value for Ri. Show your work! Do not make approximations. Vin 5V W 30K 20K 5V W WWW 2K 500 5V WH 5K C1 C2 Vo
Working on past exams with no answers so need help with working out of the answer more than the actual answer itself.
In a self-biased FET amplifier given in the figure, Vdd=20V, Rs=1kohm VGSQ=-2.6V, IDQ=2.6mA. The transistor has specific IDSS=8öA Vp=-6V and Gos=25μS. When 12mV AC voltage is applied to the transistor input, which of the following will be the RD resistor value for the output voltage to be -24.85 mV? Please fast.
Vi RB Vcc Rc our A BJT (B=200) is implemented in an amplifier circuit, with a VCC of 15 volts. One wishes to set the Q point at IC = 5.76 mA and VCE = 6.73 volts (DC). Determine RB.
2) Consider the circuit given below. (Assume: K-4mA/V', Vt=-1V, A=0, (K= µCox.(W/L)) da Perform DC analysis and calculate Va. Vsg, Vs, voltages, and Ip, gm, ro values bo Draw a small-signal equivalent circuit Co Calculate Av, Rin, Rout values as shown on the schematic Also ) satwaton mode Test for Fill inthe table VG VSG O2m A Rin Vs QUin ID vo Coo 9m Ro Av Rout Rin Rout
1
This problem is AC analysis problem. DC analysis is not needed to answer the question. A) If we assume that the peak voltage of Vbe must be less than 10 mV to avoid small signal violations determine the value of Rsig if Vi has a peak amplitude of 1 V and Is = 1mA. Hint: Don't forget r!! Answer: Rsig =. B) If you did the DC analysis on this problem and calculated Vc = 50 mV and Vs = -100 mV what is the maximum amplitude of the output voltage while the circuit stays in active mode. Answer: Vo,max =, When you "verify" a mode of operation you will need to calculate all three voltages (Vc, Ve, VE for BJTS and VG, Vs, Vp for MOSFETS) and show the correct two conditions are satisfied. Assume Capacitors acts like open circuits at DC and short circuits for AC. > Assume the following: 5V o Beta = 100 O VBE = 0.7 o V: (Thermal) = 26 mV o Vr (Threshold) = 2V O VA = - o For MOSFET saturation mode: assume: lp = K(VGs-Vr)? (Assume K = 10 mA/V²). 5kn C2 01 C1 Rsig 1kn 10k Vi IIs :C3 1mA -5V

SEE MORE QUESTIONS

Recommended textbooks for you

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

SEE MORE TEXTBOOKS