A Y-connected balanced three-phase generator with an impedance of 0.4j0.3 per phase is connected to a Y-connected balanced load with an impedance of 24 + j19 per phase. The line joining the gen- erator and the load has an impedance of 0.6 + j0.7 per phase. Assuming a positive sequence for the source voltages and that Van = 120/30° V, find: (a) the line voltages, (b) the line currents.

A Y-connected balanced three-phase generator with an impedance of 0.4j0.3 per phase is connected to a Y-connected balanced load with an impedance of 24 + j19 per phase. The line joining the gen- erator and the load has an impedance of 0.6 + j0.7 per phase. Assuming a positive sequence for the source voltages and that Van = 120/30° V, find: (a) the line voltages, (b) the line currents.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.21MCQ: The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts....

See similar textbooks

Similar questions

A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
Please Answer My Questions in 30 minutes i'm very needed... Please thank u...
A balanced Y-connected generator with terminal voltage Vbc 5 200/08 volts is connected to a balanced-D load whose impedance is 10/408 ohms per phase. The line impedance between the source and load is 0.5/808 ohm for each phase. The generator neutral is grounded through an impedance of j5 ohms. The generator sequence impedances are given by Zg0 5 j7, Zg1 5 j15, and Zg2 5 j10 ohms. Draw the sequence networks for this system and determine the sequence components of the line currents.
Two balanced loads are connected to the a 240kVrms60Hz line as shown in the figure below. Load 1 draws30kW at a power factor of 0.6 lagging and load 2 draws 45 kVAR at power factor of 0.8 lagging. The real power, reactive power, and magnitude of the line current absorbed by the combined load is close to kW, kVAR, and A. Two balanced loads are connected to the a 240kVrms 60Hz line as shown in the figure below. Load 1 draws 30kW at a power factor of 0.6 lagging kW. and load 2 draws 45KVAR at power factor of 0.8 lagging. The real power absorbed by the combined load is close to Balanced load 1 Balanced load 2
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
Three single-phase transformers are connected in delta-delta to step down a line voltage 138 kV to 80 kV to supply a manufacturing plant. The plant draws an active power of 24 MW at a lagging power factor of 0.89. Calculate apparent power in MVA drawn by the plant.
Hi . Need a solution and final answer for this question
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
Question 2 A Load ZL is connected in parallel with an impedance of -j120 Q. The parallel combination is supplied by a source Vs = 4000° Vrms, that generates a complex power of 1.6 + j0.5 KVA. Find a) Complex power delivered to Load ZL. b) Power Factor of ZL. c) Power Factor of the Source.