C₂ C₁) 5 MW. Thermal generahim sla kion hydro station has has - overall eSSicieny - 30% water discharge for 30 30 days of 5*/68 m³ 3 Kalmific value -7500 legal head of Dan = 30m plant capacity factor = 60% Fond Find the fuel mut in by "For 5 days small efficiency of 80% overall Load factor of 70% find. The max. generation output by the plant in for for the period of 30 days

C₂ C₁) 5 MW. Thermal generahim sla kion hydro station has has - overall eSSicieny - 30% water discharge for 30 30 days of 5*/68 m³ 3 Kalmific value -7500 legal head of Dan = 30m plant capacity factor = 60% Fond Find the fuel mut in by "For 5 days small efficiency of 80% overall Load factor of 70% find. The max. generation output by the plant in for for the period of 30 days

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

C. A single phase full converter feeding RL load has the following data: source voltage 230V(RMS), SOHZ.R-2.52 L=very large, firing angle -30"f the load inductrance is large enough to make the load current constant then i Sketch the time variation of sounce voltage source current, load voltage, load current current through one thyristor and voltage across it H. Compute the average value of load voltage and load current, Derive the formula.
Three phase Bridge rectifier operated from a 380V, 50Hz source throughout three-phase Y/Y connected transformer with ration 2:1. The load current has continuous character with negligible ripples and average thyristor current of 15A. The circuit inductance per phase is 1.2mH. The rectified voltage due to overlapping angle is 90 % of that voltage when this angle is neglected. 1- How much will the voltage drop be due to circuit inductance * 2- How much will the dc average voltage Vdc(alpha) be. 3- How much will the firing angle be ? 4- The overlapping angle. 5- How much is the percentage change of the output dc power if the thyristors T2, T4 and T6 are replaced by three diodes D2, D4, D6. 6- How much will be the maximum RMS phase current for the mentioned in previous task circuit ( semi-converter). 7- If an additional of 1 mH inductances are added to the existing inductances in the phases , how much will the overlapping angle be. The dc load current is kept constant & the…
Consider the circuit shown in figure 2-8. the circuit operates at 60 hz, the rms of the voltage is 120 volts, the resistor has a value of 40 ohm, the inductor is 0.1592 H, and the capacitance is 33.16 UF. a) Find the impedance of the inductor and the capacitor. b) Find the current in each leg of the circuit and the total current from the source. c) Draw a phasor diagram showing the source voltage and all the currents. d) Find the total impedance of the RLC parallel combination
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
Trial example of how to use Kirchhoff analysis to determine the initial current in each section along with its direction and the potential difference across the load
Could you solve the question ?
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Please show steps and work