not use ai please 1. In NI Multi Sim, find, and display, the resistor values closest to the values below... * (Be sure to SAVE your results)22K, 110K, 2.3M, 33, 56K, 47K2. In NI Multi Sim, connect, and display, the resistors below together to get the total resistance value...162.2K, 25.6K, 54, 10.75M, 6.8K, 120What is the total resistance? * (Be sure to SAVE your results)

Answered: Image /qna-images/answer/fae23b68-c73d-49d8-af8d-fda16e2ad1f5.jpg

Answered: 1. In NI Multi Sim, find, and display,…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

In step 2 you measured the voltage across each of the LEDs. This is their “forward voltage” that is referred to in the LED component page, which is the voltage required to light the LEDs. Notice that the combined forward voltage of D1 and D2 is greater than 3.3V, the LEDs will not light up at all. You should also have noticed that the forward voltage for one of the LEDS is lower than the forward voltage for the other LED. Some LEDS require less energy to light than others. Since D1 and D2 are in series, the same current will flow through each, but the different voltages across each LED reflect the different energy requirements. Finish each statement below, bears on this information and in the measurements you took in step 2 The measured forward voltage across D1 in this step is ________ The measured forward voltage across D2 in this step is ________
Question 3 (a) Briefly explain what is the per-unit systero. (b) A resistance of 60n is selected as the base resistance in a circuit consists of three resistors. If R, =1002, R, =30002 and %3D R, = 200 calculate the per-unit vahue of each resistance. %3D (c) A power of, P-25KW and a voltage of, E-2400V are selected as the base power and base voltage of a power system respectively. Calculate the value of the base impedance, Z, and the base current, I,. (d) A resistor bas a per-nnit value of 5.3. Given the base power is P=250KW, and the base voltage is E,-12470V, calculate the ohmic value (actual value) of the resistor. (e) A 4000 resistor caries a cucrent of 60A. Given the base valne of voltage, E, 4KV, the base value of power, P, 500KTF, the base value of current, I, =125.4, and the base value of resistor, 2, = 320 calculate the following: i The per-unit resistance. ii. The per-unit current. ii. The per-unit voltage across the resistor. iv. The per-unit power.
Typing format..
3. Find the equivalent resistance seen between the indicated nodes, in terms of R. The resistors that are in parallel let them be indicated as ()//() without making the complete calculation. a) Between nodes A and B. b) Between nodes F and G. c) Between nodes B AND E. d) Between nodes D AND F.
Use this graphic for Questions 1, 2,3, 4, and 5. R2 2kQ R1 6000 11 200mA
Type your question here In a box there are 100 resistors having resistance and tolerance as shown in the following table. Let a resistor be selected from the box and assume each resistor has the same likelihood of being chosen. Define three events A as draw a 47? resistor, B as draw a resistor with 5% tolerance and C as draw a 100Ω resistor. Find ? (?/?), ? (?/?),? (?/?).
Please help with a, d, f, h. I don't know why my values are coming out incorrect even though the units are correct.
D Question 19 A theoretical battery pack is made from the 4000 mAh Li-lon battery cells tested in lab in a 3S2P configuration. What will be the charging voltage limitation for testing this battery pack using GCPL? Enter your answer in V.
Recommend a way to modify the semiconductor, without changing the dimensions of the bar, so that the current flowing through the bar increases by 250% when the same voltage is applied. Justify your answer with your written statements and proof of calculations.
The circuit displayed below is comprised of resistors, a battery, capacitors and a single pole double throwswitch (SPDT). When switch is in the position of A, the battery is connected to the circuit. When the switch is in the position of B, the battery is then replaced with a wire. In the beginning, the switch is open, and all capacitors are firstly uncharged. The switch is then flipped in the position of A, so the battery is in the circuit. Then, 30.0 seconds after the switch is then submitted to the position of A, what will the potential difference be beyond C3?
Two batteries, A and B, are connected in parallel and an 80 ohm resistor is connected across thebattery terminals. The e.m.f. and the internal resistance of battery A are l00V and 5 ohm respectively,and the corresponding values for battery B are 95V and 3 ohm respectively. Find (a) the value anddirection of the current in each battery and (b) the terminal voltage
Part A shown in image, part B) for the circuit find the load resistance (RL) that draws the maximum amount of power from the rest of the circuit and calculate the maximum power that can be delivered to RL c) calculate the range of resistance values for rl that will result in more than 10 watts of power absorbed in rl

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS