Question 3(a) Briefly explain what is the per-unit systero.(b) A resistance of 60n is selected as the base resistance in a circuitconsists of three resistors. If R, =1002, R, =30002 and%3DR, = 200 calculate the per-unit vahue of each resistance.%3D(c) A power of, P-25KW and a voltage of, E-2400V are selectedas the base power and base voltage of a power system respectively.Calculate the value of the base impedance, Z, and the basecurrent, I,.(d) A resistor bas a per-nnit value of 5.3. Given the base power isP=250KW, and the base voltage is E,-12470V, calculate theohmic value (actual value) of the resistor.(e) A 4000 resistor caries a cucrent of 60A. Given the base valne ofvoltage, E, 4KV, the base value of power, P, 500KTF, thebase value of current, I, =125.4, and the base value of resistor,2, = 320 calculate the following:i The per-unit resistance.ii. The per-unit current.ii. The per-unit voltage across the resistor.iv. The per-unit power.

Answered: Image /qna-images/answer/65a0b2f2-26ff-4699-8e6d-a5e8909351a1.jpg

(a) Briefly explain what is the per-unit systerm. (b) A resistance of 60n is selected as the bese resistance in a circuit consists of three resistors. If R, = 1002 R, =3000n and R3 = 202 calculate the per-unit value of each resistance. %3D (c) A power of, P-25KW and a voltage of, E-2400V are selected as the base power and base voltage of a power system respectively. Calculate the value of the base impedance, Z, and the base current, I,

(a) Briefly explain what is the per-unit systerm. (b) A resistance of 60n is selected as the bese resistance in a circuit consists of three resistors. If R, = 1002 R, =3000n and R3 = 202 calculate the per-unit value of each resistance. %3D (c) A power of, P-25KW and a voltage of, E-2400V are selected as the base power and base voltage of a power system respectively. Calculate the value of the base impedance, Z, and the base current, I,

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

From the diode circuit shown below, If E-40 V and RL=8002, determine the current supplied from the battery, the voltage across the load resistance, and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 1 02. E= D₁ Z D. RL a. The Current supplied by battery is D₂ D3
Please solve this question queckly
Shown below is a diode circuit. If the input signal Vs = 31 Vp-p and the DC voltage Vdc = 8 V, what is the output voltage (in volts) of the circuit during the negative alteration? No need to show your solution. Just write your numeric answer on the space provided. Round off your answer to 2 decimal places. C1 ... + Vdc 1.0kn Vo Vs Si D1
*Use 4 decimal places. For the circuit below, determine the diode voltages VD1 and Vp2, diode currents Ip1 and Ip2, and voltage across the resistor, VRLIMIT- Use ideal model. Assume r'a (for both diodes)=200. Note D, is Germanium, D2 is Silicon, VBIAS = 14V and RLIMIT = 760 ohms . VD1 = Blank 1 V; VD2 = Blank 2 V; Ip1 = Blank 3 mA; ID2 = Blank 4 mA ; VRLIMIT = Blank 5 V ... Capture3.JPG +Vo1- +VRLIMIT- +V02- Io1 Io2 V BIAS
for The Gircuit shown in figure if (B =50) tind The values of CIe). and of Then express The change in value by apercentage + 15U RB, = 100Ka R82 = 50 KQ RE 3K2 %3D
*Use 4 decimal places. For the circuit below, determine the diode voltages VD1 and VD2, diode currents Ip1 and Ip2, and voltage across the resistor, VRLIMIT- Assume r'a (for both diodes)=200. Note D, is Germanium, D2 is Silicon, VBJAS = 22V and RLIMIT = 2 kohms. VD1 = 0 V; VD2 = 0 V; Ip1 = Blank 3 mA; Ip2 = Blank 4 mA ; VRLIMIT = Blank 5 v Use ideal model. Capture3.JPG +VD1- +VRLIMIT +Vp2- Ip2 VBIAS 두
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
Find the equivelent resistance of the circuit below. (Rin)Conduction diodes' resistance is 0Insulating diodes' resistance is infinite.R1 = 10 ohm
A diode is a two-terminal, electronic device made using semiconductors that is designed to prevent current from flowing in a particular direction. The symbol is a triangle pointing in the direction that (positive) current is allowed to flow and a wall preventing (positive) current from flowing in the opposite direction: 1: A diode has two modes, "on" and "off". When "on", current flows, and when "off", no current flows. We generally view diodes as either "ideal" or "modeled", as described below. "Ideal" view of a diode + The "ideal" diode is either a short circuit or an open circuit. Specifically, when the voltage across its terminals is negative, no current flows, and when current flows, there is zero voltage across its terminals, as pictured below: Diode "Modeled" view of a diode +51 Diode V Ideal Diode "Off" i=0| + U≤0 + I Therefore, with current i and voltage v defined as shown on the left above, for an "ideal" diode: • Current i cannot be negative. Voltage v cannot be positive. .…
a) Determine the output voltage for all input voltages values. b) Sketch the overall output waveform, Vo(t).
For circuit given in Figure 3 use Complete Diode Model andfind the voltage across R1 and R2 andtotal current flowing in this circuit. Giventhat diodeforward resistance is 15 Ohmsfor D1 and 10 Ohmsfor D2, also reverse current flowing acrossD2 is 20 micro Amperes. DI Ri 50 Q ww D2 Rz100 N KH 10 V R3150 2 www Figure 3
For a diode connected NMOS, determine the required drain to source voltage (in V) to produce a drain current of 9.41 µA. Assume the following specifications for the NMOS: k = 6.91 µA/V2, W/L = 7, VTH = 0.9 V, LAMBDA = 0 V-1. Express your answer using 3 decimal places.