Q3. Determine the minimum and maximum values of the load current for which the Zener below will operate correctly. Also determine what is the minimum value of load resistance R. Max that can be used. The following values are provided: V = 12 V, I = 1 mA and I = 50 ZK mA. Assume an ideal Zener diode with no resistance after it has switched on and thus a constant voltage drop of 12 V over it when ON. R 470 2 VIN 24 V RL Answer: Minimum load current: () Answer: Maximum current: () Answer: Minimum load resistance: ()

Q3. Determine the minimum and maximum values of the load current for which the Zener below will operate correctly. Also determine what is the minimum value of load resistance R. Max that can be used. The following values are provided: V = 12 V, I = 1 mA and I = 50 ZK mA. Assume an ideal Zener diode with no resistance after it has switched on and thus a constant voltage drop of 12 V over it when ON. R 470 2 VIN 24 V RL Answer: Minimum load current: () Answer: Maximum current: () Answer: Minimum load resistance: ()

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)
When a conventional Silicon diode is reversed-biased with a voltage high enough such that there is a very large current present, the voltage value this occurs at is referred to as the: a) Breakdown voltage b) Breakup voltage c) Hammer voltage d) Roller voltage O b O d O c a o o o o
From the diode circuit shown below. If E=40 V and RL=400, determine the current supplied from the battery. the voltage across the load resistance. and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 2 0. RL E= a. The Current supplied by battery is b. The Voltage across Load resistance RL is c. The Voltage across diode D2 is
1. Determine and sketch I2 and I3 for Vi as shown if both diodes are a. Ideal diodes b. Constant voltage drop of .7 V Please answer in typing format please ASAP for the like please
If a certain zener diode has a zener voltage of 6.2 V, it operates in Select one: a. forward conduction b. zener breakdown c. regulated breakdown on d. avalanche breakdown
R₁ 2,0m D₂ $2.5 R₂ www D₁ ☆ Vo Figure 1: Precision Rectifier 1. Characterize the relationship of input vs. output for the circuit in Figure 1. That is, find an expression for . You can use the constant voltage drop model for the diodes. Vi
JAE To sketch the characteristic curve of the diode you need to vary voltages on diode and measure current flowing during forward and reverse bias condition. Fill up the table below using circuit shown and vary battery voltages. Measure voltage and current of diode then sketch the graph. Voltage X axis and Current Y axis. A Battery Diode voltage Voltage 0.1V 0.3V 0.5V 0.7V 1.0V 2.0V 3.0V 10.0V Diode Current Forward Bias Condition +||| V Battery Diode Voltage 0.1V 0.5V 2.0V 5.0v 10v 20V 25V 30V Voltage Note: used any electronics software to perform this activity Reverse Bias Condition Diode Current ELECTRONICS ENGINEERING (ECE) DEPARTMENT SINCE VIT
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
For the circuit in the figure, let V input = 8V, Ri = 12ohms, RL = 10ohms, and VZ = 3.3V. Determine the voltages and currents of the resistors and the current of the zener diode.
(c) Reverse recovery is a common problem in a diode. It can increase switching losses, increase forward voltage and induce voltage surge. (i) Explain how reverse recovery can increase switching losses in a diode. (ii) Figure Q1(c) shows that characteristic of reverse recovery in a diode. Based on the figure, calculate the peak reverse recovery current I, I (A) dls dt 30 A Q,, 1 us 3 us Figure Q1(c): The characteristic of reverse recovery in a diode
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
Calculate the current (I) through the diode and voltage across the resistor (Vout). Assume V1 =15V,R1=6KN. Ge Vout V1 R1 Diode D1 is ON or OFF? Choose... Vout= Choose... Current (I) = Choose... v