0 10:28 PM M▸ ← ☐ Analogue El... Q Analogue Electronics Assignment One a). List and explain any 5 types of resistors b) Describe the following mechanisms [10] [12] i) avalanche breakdown ii. Zener breakdown c) With the aid of a diagram describe and explain the operation of a voltage quadruapler d) Design a clamper to perform the function indicated in fig 1 [10] [6] 20 V -20 V Ideal diodes Design fig 1 For the emitter-stabilized bias circuit of Fig. 4.90, determine: a. 1BQ b. lcg c. VCEQ d. Vc e. VB. f. VE- 20 V 510 ΚΩ IBQ VB 2.4 ΚΩ Ico + VCEQ 1.5 ΚΩ VC B-100 OVE Fig 4.90 Δ +30 V --10 V 313 [12] A 20

0 10:28 PM M▸ ← ☐ Analogue El... Q Analogue Electronics Assignment One a). List and explain any 5 types of resistors b) Describe the following mechanisms [10] [12] i) avalanche breakdown ii. Zener breakdown c) With the aid of a diagram describe and explain the operation of a voltage quadruapler d) Design a clamper to perform the function indicated in fig 1 [10] [6] 20 V -20 V Ideal diodes Design fig 1 For the emitter-stabilized bias circuit of Fig. 4.90, determine: a. 1BQ b. lcg c. VCEQ d. Vc e. VB. f. VE- 20 V 510 ΚΩ IBQ VB 2.4 ΚΩ Ico + VCEQ 1.5 ΚΩ VC B-100 OVE Fig 4.90 Δ +30 V --10 V 313 [12] A 20

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

What is CEMF?
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Value: Student No. Last 1 digit ( will be selected as kΩ, LastThose whose number is "0" get "9")a) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
Please help with the solution.
An FWR using a centre-tapped Transformer Supplies an average voltage of 120V to a 250 kΩ load Calculate (a) the peak value of output voltage (b) The required Transformer secondary voltage (rms value) (c) Average Current delivered to load (d) Average current through each of the diodes. (e) Peak Current through each of the diodes (f) PIV requirements for each of the diodes. AC supply voltage is 230V and assume ideal diodes.
Z01 @ C Asiacell l. positive clipper negative cli 03_diode_clipper_clamper_multiplie... pi 5/12 7. Questions: A. The positive peak voltage of a positive clipper is: 1- 0 V 2- 0.6 V 3- Equal to the input peak voltage 4. 1.2 V B. Why is the positive peak voltage in the negative clipper not cut? 1- The diode is forward biased 2- The diode is reversed biased C. In a positive polarized clipper we found the voltage source in series to the diode equal to be +5V. Which is the cut level of the positive voltage? 1- 0.6 2- Equal to the input peak voltage 3- 5 V 4- 5.6 V 6/12
AN Sesli oku 1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm32k İm-(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V. B-What should the tolerances of the resistors be so that the Vm class is at most 1.5? (resistors have the same tolerances) ult) R2 本 R3 20k 18k R4 k: k2 10k
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Q1)Design moving coil ammeter as a voltmeter to read 15 V (RMS) alternating voltage. If the internal resistance of the ammeter is 5 K2, the voltage across the internal resistance is 0.5 v and the resistance of the diodes in the forward direction is 1 K2, find the multiplier resistance and sensitivity. Assume half wave rectification and a shunt resistance across the meter. The value of the shunt resistance across the ammeter is 2.5 KQ. Q2) Re-design the question above for full wave rectifier (without Rsh)
Question-3 Can you throw the emergency solution? I would appreciate it if you write legibly.
5) For a single phase full wave bridge rectifier with a resistive load if the input voltage is 225 V, 50 Hz with the value of resistance is 25 ohms. Compute the value of ms value of load voltage and average value of load voltage by formulating the equations with all steps
Q1)Design moving coil ammeter as a voltmeter to read 15 V (RMS) alternating voltage. If the internal resistance of the ammeter is 5 KQ , the voltage across the internal resistance is 0.5 v and the resistance of the diodes in the forward direction is 1 KQ, find the multiplier resistance and sensitivity . Assume half wave rectification and a shunt resistance across the meter. The value of the shunt resistance across the ammeter is 2.5 KQ. Q2) Re-design the question above for full wave rectifier (without Rsh)
The ripple factor for pure dc is Answer: For the given circuit below, it operates on a peak-to-peak input voltage of 390.1 V, F= 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1, D2 AC Input Vsec (Source) .03 D4 Load O 27.31 O 18.11 O 13.93 O 20.91