9. Use SPICE or a similar circuit analysis package to simulate a Cockcroft-Walton multiplier withtwo stages (i.e., a circuit like that in Figure 5.19, but only up through C3, C4, and D4). The inputis a 120 VRMS 60 Hz sine wave. Use C = 0.01 F. What maximum load can be supplied withoutdropping the steady-state output potential by more than 10%?

Here's a step-by-step process to approach this analytically.Step 1: Peak Output Voltage for…

Answered: 9. Use SPICE or a similar circuit…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explaion the concept of RL Circuits in relation with Linear Equation?
4: Design a buck converter to produce an output voltage of 18 V across a 10-_ load resistor. The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the rms current in the inductor and capacitor. Assume ideal components.
Exercise Design a buck converter to produce an output voltage of 18 V across resistor. The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the RMS current in the inductor and capacitor. Assume ideal components. Assume the inductor be 25 percent larger than the minimum to ensure that inductor current is continuous.
Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs 160 V. The switching period is 0.25 ms and the duty cyclek is first set to 0S. The load is resistive with R-10 OHMS. When the switch is ON, a voltage drop across the switch is noted of Vch 1V. The RMS output voltage vo is equal to 1124V. The RMS input current and the conduction losses are equal to: Select one: O a.7.95A and 7.95W O b. 11.24A and 11.24w OC. None of these O d. 11.24A and 1263W
Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is an inductive load with R=10 Ohms and L-10 mH. The switch is ideal. The average source current is 4A. The ripple factor of the input current RFs is equal to: Select one: O a. None of these O b. 0% C. 100% d. 50% Clear my choice
Do calculation. This is not a simulation problem
5.12 Analyze the circuit shown in Figure P5.12 and determine the following when ß = 200 and VBE = 0.7 V: a. Ico and VCEQ. b. A, and Rin- c. A₁. d. Maximum undistorted output voltage swing. C →∞ नह + 100ΚΩ in R₂ 12kΩ Σ R, allı Vcc=+10V 4ΚΩ 20092 VBE=0.7V B=200 C→∞ iload 20092 O Rload VEE=-10V + Figure P5.12 V Tc→∞ out 6ΚΩ
A boost converter is required to have an output voltage of 8 V andsupply a load current of 1 A. The input voltage varies from 2.7 to4.2 V. A control circuit adjusts the duty cycle to keep the outputvoltage constant. If the switching frequency is 200 kHz, determine:i. a value for the inductor such that the variation in inductorcurrent is no more than 40% of the average inductor current forall operating conditions.ii. a value for the capacitor such that the output voltage ripple isno more than 2%.iii. in case the OFF period is reduced by 30% for constantfrequency operation, find the new output voltage
Design a voltage regulator circuit to supply a constant voltage of (10 V) across a resistive load of (10 ). The minimum Zener current is (50 mA) and maximum current is (800 mA). AssumeRs=10 andFind:- 1- the maximum and minimum source voltage. 2- at the maximum source voltage, find the minimum load resistance. 3- at the minimum source voltage, find the maximum load resistance. 4- minimum and maximum power dissipated in the Zener diode.
Q3) A. In a class-A chopper circuit an ideal battery of terminal voltage 100 V supplies a series load of resistance 0.25 2, and a series inductor of 1 mH. The load consists of a series battery.of 10 V. The control time T of the chopper is 2.5 ms and the ON time is 1 ms. (a) Specify whether the current will be continuous or discontinuous? (b) Calculate the average output voltage Vo, and average output current Io. (c) Calculate the maximum and minimum values of the output current. (d) Sketch to scale compatible waveforms for Vo, Io, Ich, and Is.
Q1. a) Figure Q1 is a single phase 2-level voltage source converter (VSC) with a total DC voltage V-1000V. A PWM scheme, by comparing a reference value with a 1kHz triangular waveform, is used to control the switches S₁ and S2, and output 340v at Vo. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle and the modulation index. Va + 2 it Va d + TS₁ V {1+5₂ = Figure Q1 A single phase VSC
Part 2: In a step-up converter, consider all the components to be ideal, Let Va be 8-16 V, V. 24 V (regulated), fs-20 kHZ, Po ≥ 6 W. i). Calculate the minimum inductance L required to keep the converter operation in continuous-conduction mode under all conditions. ii). Specify the value of inductor for a maximum ripple of 3%. iii). Design a capacitor for part (i) and (ii) with a voltage ripple of less than 2%.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS