A 240 V series motor develops a torque of 120 Nm at a speed of 900 rpm. The armaturewinding resistance is 0.20 and the series field winding resistance is 0.1 Q. For a constant loadtorque find the new speed of the motor when a diverter resistance of 0.1 Q is placed across theseries field winding.

Given Data:Supply Voltage, V = 240 V Torque, T = 120 Nm Speed, N = 900 rpm Armature resistance,Ra =…

Answered: A 240 V series motor develops a torque…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
• Q5/ in a DC motor. List and describe the types of losses that occur
Please question 4
A D.C. series motor of resistance 1 ohm between terminals runs at 800 r.p.m. at200 V with a current of 50 A. Find the speed at which it will run when connectedin series with a 5 ohms resistance and taking the same current.
A repulsion start, induction run motor is used to drive a fan. The motor has a rated power of 2kW and operates at 220V. The repulsion start winding has a resistance of 0.5 ohm while the induction winding has a resistance of 0.3 ohm. Determine the total loss in the motor, assume 0.8 pf.
A 3-phase, 50-Hz induction motor with its rotor star-connected gives 500-V(r.m.s.) at standstill between the slip-rings on open-circuit. Calculate the current and power factor at standstill when the rotor winding is joined to a star-connected external circuit, each phase of which has a resistance of 10 Q and an inductance of 0.04 H. The resistance per phase of the winding is 0.2 Q and its inductance is 0.04 H. Also, calculate the current and power factor when the slip-rings are short-circuited and the motor is running with a slip of 5 per cent. Assume flux remain constant.
tal At rest condition, the slip of induction motor is 0. Select one: True False In DC series motor when flux decreases, the speed w decrease zero remains same increase
A large 3-phase, 4160 V, 60 Hz, squirrel-cage induction motor draws a current of 400 A and the total active power of 2500 kW when operating at full-load. The corresponding speed is accurately measured and is found to be 1178 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.15 0. The total iron losses are 26.5 kW and the windage and friction losses are 15 kW. Calculate the following: The power factor at full-load The active power supplied to the rotor The total I²R losses in the rotor The load mechanical power [kW], torque [kN.m], and efficiency [%] a. b. C. d.
In a 3-phase, 4-pole induction motor, The power crossing the air gap of a 60 Hz is 42.6 kW, and the power converted from electrical to mechanical form in the motor is 39.6 kW. If the total mechanical losses are 1000 W, find the load torque of this motor? Select one: O a. None O b. Tload = 208.4 N.m. O c. Tjoad = 232.6 N.m. O d. Tjoad = 220.3 N.m. Clear my choice
Find the value:
3. A 440V 60-hp six pole 60 hz A connected induction motor has the following parameters R1=0.048 R2= 0.035 Xm= 9.50 X1= 0.33 0 X2= 0.37 0 Pcore= 600W PF&W= 350W Use the Thevenin's Equivalent circuit concept to find: (a)Vth and Zth seen by the rotor circuit (b)The slip at which maximum torque occurs (c) the value of Max/pullout Torques (d) The starting torque.
PROBLEM-1 PROBLEM-2 PROBLEM -3 Lin C in R in milli micro V C1 C2 C3 C3 C5 C6 Im X A henry farad V F oms 42 13 23 26 25 9. 19 112 102 0.42 42 102 80 140 60

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

A 240 V series motor develops a torque of 120 Nm at a speed of 900 rpm. The armature winding resistance is 0.20 and the series field winding resistance is 0.1 Q. For a constant load torque find the new speed of the motor when a diverter resistance of 0.1 Q is placed across the series field winding.