Consider a step down converter with a resistive load. it is supplied by a DC power source of magnitude Vs 160 V. The switching period is 0.25 ms and the duty cyclek is first set to oS. The load is resistive with R-10 OHMS When the switch is ON, a voltage drop across the switch is noted of Vch 1V. The RMS output voltage Vo is equal to 11243V. The RMS input current and the conduction losses are equal to: Select one: O a. 7.95A and 7.95W

Consider a step down converter with a resistive load. it is supplied by a DC power source of magnitude Vs 160 V. The switching period is 0.25 ms and the duty cyclek is first set to oS. The load is resistive with R-10 OHMS When the switch is ON, a voltage drop across the switch is noted of Vch 1V. The RMS output voltage Vo is equal to 11243V. The RMS input current and the conduction losses are equal to: Select one: O a. 7.95A and 7.95W

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A de chopper has a load resistance of 202 and input voltage V,-220 V. When the chopper is ON, its voltage drop is 1.5 V and chopping frequency is 10 KHz If the duty cycle is 80%, determine average output voltkge, ms output voltage and chopper ON time.
1. For the above Boost converter, what is the duty cycle? a. 0.95 b.0.75 c. 0.25 d. None of the obove 2. For the above Boost converter, what are the average current flowing in the MOSFET and diode? a. 12A, 4A b. 12A, 12A c. 4A, 4A d. 16A, 4A 3. For the above Boost converter, what is the peak switching current flow in the MOSFET and diode? a. 19.75A, 19.75A b. 15.75A, 15.75A C. 19.75A, 15.75A d. None of this 4. what is the max voltage stress on the MOSFET and diode? a. 10V, 10V b. 10V, 40V c. 40V 40V, d. none of this 5. what is the output voltage peak to peak ripple? a. 0.3V b. 0.1V c. 0.6V d. none of the above
Industrial Electronics If the given types of DC-DC Converter has an input voltage of 25V. The output voltage of each converter using a duty cycle of 0.4s. a.) Buck Converter Vout?b.) Boost Converter Vout?C.)Buck-boost converter Vout?
DERIVE AVERAGE OUTPUT VOLTAGE EQUATIONS FOR 3-PHASE SEMI CONVERTERS.
Q1:THE CHOPPERS changing the level of DC voltage starching the cycloid -converter Q1/b: The converter in bust-buck converter has Two quadrant behaviors positive and negative one positive Quadrant behavior Qlic: Free-welling diode help to Smooth discharging the remining power in the SCR copper CCT Orientation the currents through the chopper CT Q1/d: The boost DC-DC converter is used to increase the input voltage level of its output side decrease the input voltage of its out put voltage Qle: Boost-Buck converter device built in a combination of step up chopper step up and Step down choppers
i need the answer quickly
I need the answer as soon as possible
The input voltage (vin) of the following circuit is a sinusoidal signal with an amplitude of 2Vrms,consider a silicon diode.graph the output voltage ?? and the current across the resistor.
A three phase full controlled converter is supplied by a phase voltage Vs=120V, 60 Hz. Consider a resistive load R=10 N. If the RMS value of the output current is equal to 20A and the input Volt Ampere VA = 5000VA, then the output power Po and the power factor would be equal to: Select one: O a. 3000W, 0.7 lagging on O b. 3196.84W, 0.372 lagging Oc 3196.84W, 0.75 lagging O d. 4000W, 0.8 lagging
explain the efficiency of tuned circuits as frequency delective circuits in paragraph form
Build an AC/DC dual power supply circuit that draws a 60Vp-p sinusoidal voltage, to provide a dc output voltage of +15 V. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?
A three phase full converter is supplied by a phase voltage V5-120V, 50 Hz. The rectifier supplies a resistive load R=100 Q. Suppose that the average output voltage is 40 % of the maximum possible average output voltage. The delay angle a would be equal to: Select one: O a. 44.42deg O b. 88.42deg O c. 66.42deg O d. 22.42deg TOSHIBA