Consider a step down converter supplied by a DC power source of magnitude Vs = 220 V. The switching period is 0.1 ms and the duty cycle k is set to 0.5. The load is an inductive load with R=5 Ohms and L=10 mH. The switch is ideal. The RMS converter current IR is equal to 15.56A. The ripple factor of the input current RFs would be equal to: Select one: Oa.0% O b. 50% O c. 100% O d. None of these

Consider a step down converter supplied by a DC power source of magnitude Vs = 220 V. The switching period is 0.1 ms and the duty cycle k is set to 0.5. The load is an inductive load with R=5 Ohms and L=10 mH. The switch is ideal. The RMS converter current IR is equal to 15.56A. The ripple factor of the input current RFs would be equal to: Select one: Oa.0% O b. 50% O c. 100% O d. None of these

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6)For the CRO Sine waveform shown in figure, determine (a) Time period, (b) frequency, c) amplitude (d) peak-to-peak voltage and e) RMS voltage.
Working principle of boost DC TO DC converter
Question 14 In the given circuit, a step down transformer with an RMS voltage as 110V / 11-0-11 V is used with RL = 1 KQ. Not yet answered Assume diode as Germanium and the input frequency is F= 50HZ. Marked out of Dy 3.00 P Flag question RL D, 1- Name the given circuit . 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms. B I 00000
-Design a buck converter that has an output of 12 V from an input of 18 V. The output power is 10 W. The output voltage ripple must be no more than 100 mV p-p. Specify the duty ratio, switching frequency, and inductor and capacitor values. Design for continuous inductor current.
Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). 2- The ripple voltage. Vot Vm = 12 V 3- The Vde value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. Vip = 0.1 V (assume ideal diodes) T=0.01 sec. tisec) Q3) V in Design a regulated circuit to supply a constant voltage of (10 V) across a resistive load of (50 2). The input voltage is shown in the figure. The minimum current for the Zener diode operation is (Izk=5mA). Find the 15 V 15 maximum power dissipated in the Zener diode. 12.5 12 V 10
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
i need the answer quickly
A single-phase converter contams three uncontrolled and one controlled power electronic switches. A smgle-phase 230 V. 50 Hz supply is given to the converter and feeding a resistive load of 47 is connected. Find theaverage power delivered to the load for a firing angle of 45°.
For the buck-boost converter, determine the duty cycle, the switching frequency, and the inductor current ripple. The output voltage ripple is about 1%. vs 10 V, mH, C 0.5 micro.F, Vout=-20 V, R-IO Q
Calculate the rms value of the output voltage of an AC-AC converter with the following specifications. Vs—110*sqrt(2)*sin(wt), Alpha Pi/6
Solve it fast fast plz
Solve it quickly please now