(c) The block diagram of a fluidic speed control system is shown in Figure 1 where the actual speed C(s) is system output and R(s) is reference speed. Show that the closed-loop transfer function is given by C(s) R(s) = Ka 100s²+s+Ka Reference Speed R(s) Valve actuator Turbine Amplifier Actual Speed 1 1 Ka 1+100s S C(s) Figure 1

(c) The block diagram of a fluidic speed control system is shown in Figure 1 where the actual speed C(s) is system output and R(s) is reference speed. Show that the closed-loop transfer function is given by C(s) R(s) = Ka 100s²+s+Ka Reference Speed R(s) Valve actuator Turbine Amplifier Actual Speed 1 1 Ka 1+100s S C(s) Figure 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Fill in the blanks with the correct choice to complete the sen 1- He always .......... about trivial things. A. Lies B. Lied C. Lying 2- I hope everything is........ Fine tomorrow. A. Will be B. Going to be C. Being 3- She was walking alone When the child............ to cry. A. Begin B. Began C. begun
Please click on pic to open it
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • An abc-phase sequence three-phase balanced wye-connected source supplies power to a balanced delta-connected load. The impedance per phase in the load is 14+j12 Ω. If the source voltage for a phase is Van=120<80° Vms, and the line impedance is zero, find the phase currents in the wye-connected source.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places • A positive-sequence three-phase balanced wye voltage source has a phase voltage of Van=100 <20° V. Determine the line voltages of the source.
Don't need to explain, but please answer all the question. 1. The resistance strain gauge can measure plastic deformation. A) True B) False 2. In order to save cost, the resistance strain gauge can be reused. A) True B) False 3. In the quarter bridge, there is only one strain gauge which resistance value will change. A) True B) False 4. The shell of inertial acceleration sensor is fixed on the measured object. A) True B) False
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: TRANSFORMERS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:An 80:5 current transformer is connected to a 5-amp ammeter. if the latter reads 3.65 amp, what is the line current?
Please give the answer in seconds as per the question
DEGREE: Electrical Engineering SUBJECT/COURSE: AC CircuitsTOPIC: Converter and Rectifier NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. REQUIRED/FIND/MISSING (with symbol/s)4. ILLUSTRATION (Required).5. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: A 1,000-kw three-phase converter delivers full load at 600volts. If the efficiency is 94percent and the power factor is 0.96, determine:(a) the direct-current output(b) the a-c slip-ring current(c) the kilovolt-ampere load delivered by each transformer.
3.The magnitude of vector product of two vector is V3 times their scalar product. What is the angle between the vector.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: TRANSFORMERS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:Connect the three 1-Φ transformers in bank:Primary winding in WYE and secondary windings in DELTA.
PROBLEM NUMBER ONE: The closed-loop transfer function of a negative unity feedback system is given by (s + 4)(s − 1) - T(s) = 55 +254 +25³ +4² +5+2 Determine the systems stability using the Routh Hurwitz Criterion for Stability. Depending on the case, use the following required method: Case 1: Apply the usual procedure of the Routh array. Case 2: Apply the Reciprocal of Roots and Reverse Coefficients Case 3: Apply Auxiliary Polynomial
please answer the questions in terms of electric car