3. A VSI connects a large battery storage system to an ac utility grid. One phase of the circuit is shown in Figure 6.38. The inverter bridge has relative phase angle 8, and is set so its wanted component lags the ac voltage by an angle . For 8 = 45° and = -30°, what is the average power per phase flowing to the ac source? What if = +30°?

3. A VSI connects a large battery storage system to an ac utility grid. One phase of the circuit is shown in Figure 6.38. The inverter bridge has relative phase angle 8, and is set so its wanted component lags the ac voltage by an angle . For 8 = 45° and = -30°, what is the average power per phase flowing to the ac source? What if = +30°?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.15MCQ: To convert a per-unit impedance from old to new base values, the equation to be used is...

See similar textbooks

Similar questions

Describe what coupling capacitors are and what are they for?
Plz solve this
q6/ Complete the blank In AC-DC power transmission system, ............................................. is used to convert the DC supply into AC supply.
Discuss uncertainty relating to voltage, DC-resistance measurements, and AC-impedance measurements.
Derive the expression of the RMS load voltage for a full wave ac voltage controller operating with an R-L type of load. Assume the load current to be discontinuous.
Q6) A three-phase to single-phase, three-pulse cycloconverter delivers power to a load rated at 100 V, 30 A, 25 Hz with power factor 0.8 lagging. a) Draw & derive the output voltage if the ap-60° b) Estimate the necessary input voltage and power factor. c) Draw the mean output voltage if the input frequency is 200Hz. M
DERIVE AVERAGE AND RMS OUTPUT VOLTAGE EQUATIONS FOR 3-PHASE SEMICONVERTERS.
2. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 60Hz respectively. The output frequency is 15Hz and the firing angle equal to 90°. The load is resistance with the value of 500. i. Draw the waveforms output voltage, output current, source current, the thyristors currents (iT, IT, IT and in). a. Calculate the rms of output voltage. b. Calculate the rms of output current and thyristor current. ii. If the firing angles of thyristors "with different firing angles technique". Draw the complete waveforms and comment on the results.
“Electronic regulators are better than resistive ones in many aspects to control AC power” – explain with suitable examples and aspects. Out of on-off and phase control used in AC regulator, describe which one is better and why. Define a cycloconverter and write its application areas.
c) What are fol d) Explain the principle of Merz prize system of protection used for power transformers. What are the limitations of thus scheme and long they are overcom. OR
4
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…