Determine the short-circuit current ISC3,0.4kV for a 3-phase short- circuit fault at F. Give your answer up to 2 decimal in kA but do not enter the unit in your answer. Transformer T1 Transformer T2 Cable C1 Isc3,6.6kV Isc3.0.4kV j0.150 2 MVA 22/6.6 kV 1 MVA 6.6 kV/400V Z=3% 25 MVA fault level 6.6 kV switchboard 400 V switchboard

Determine the short-circuit current ISC3,0.4kV for a 3-phase short- circuit fault at F. Give your answer up to 2 decimal in kA but do not enter the unit in your answer. Transformer T1 Transformer T2 Cable C1 Isc3,6.6kV Isc3.0.4kV j0.150 2 MVA 22/6.6 kV 1 MVA 6.6 kV/400V Z=3% 25 MVA fault level 6.6 kV switchboard 400 V switchboard

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 12 MVA, 132/6.6 kV, transformer having a reactance of 0.15 pu is fed from an infinite bus. The transformer feeds two motor each 6 MVA, 6.6 kV. Each motors has a transient reactance of 0.14 pu and a subtransient reactance of 0.30 pu based on its own rating. A three phase balanced fault occurs at the terminals of one motor as shown in the figure below. Find the subtransient fault current and subtransient current in breaker. M1) 132/6.6 KV СВ 38 CB Infinite Bus M2 Fault
Ql-phase step down transformer 1250 KVA, 10002200 V, 50 Hz The resistance /phase and leakage reactanceiphase of the primary winding are 0.78 2 and 4.82 and the corresponding values for the secondary winding are 0.012 and 0.002 respectively if the primary winding is connected in delta and secondary in star calculate: )The voltage to be applied at normal frequency to the primary to circulate full-load through it when the secondary is short-circuited li) The full load copper loss
Please answer all subparts than i will like a. A current transformer (CT) is rated 200/5 and has a secondary current of 4.0 A. Determine the primary current. b. A 150/5 CT has the primary conductor looped to pass through the donut three times. If the secondary current is 3.0 A, determine the primary current. c. A 60/5 CT has the primary looped to pass through the donut two times. With 25 A in the primary, determine the secondary current. d. A voltage (potential) transformer is rated for 14.4 kV / 115 V and is used to measure the voltage on an industrial power line. If the voltmeter indicates 111 V, calculate the voltage in the power line.
6. For the air core transformer circuit shown below, determine the currents la and lb in the direction shown. Express each answer in polar form. R1-302 www la ZI1=150 E=10/0 M=j20 Ze= n Z12=j62 lb R2=50 la Ib
Write in Briefly about circuit breaker, current transformer and voltage transformer
A 120 kVA, 1350/330 V single phase transformer has the following parameters: R1 = 0.34 Q, X1 = 0.59 0, R2 = 0.014 Q, X1 = 0.029 Q, Rc = 380 and Xm = 320 Q. The no load current is 4.7 A at a power factor of 0.36 lagging and the no load losses are 4.6 kW. For a full load and 0.9 power factor lagging with 300 V load terminal voltage, determine (a) equivalent circuit parameters referred to primary side, (b) percentage regulation and (c) full load efficiency. O:01 AM
The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding transformer is 5000/250 V. Calculate the load kVA for maximum efficiency. The full-load I2R loss is 1800 W and the core loss is 1500 W. Round your answer off to the nearest whole number
2) 9.2Three - 25 KVA single-phase transformers are connected in delta – delta. One of the transformers has been defected. What is the maximum real power that the transformer bank can deliver at a power factor of 0.8?
In No-load circuit of single phase transformer input power is equal to
Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent circuit elements are: As follows R1 = 0.1 02 x1 = 0.2 2 R2 = 0.25 2 X2 = 0.75 2 RO = 500 XO = 150 Q and feeds a load of 90 kVA at a voltage of 2000 volts and a power factor of 8.0 in delay. Calculate voltage and current Primary Royl ww JX eql
Assume a transformer rated 700 MVA with 145 kV on the secondary side. Determine the base current and base impedance. For the one line diagram shown, determine the pu reactances and draw the reactance diagram choosing 100 MVA and 20 kV as base values for generator. T1 T2 1 Vm Line G M G1- 60 MVA, 20 kV, X= 9% T1- 50 MVA, 20/200 kV, X =10% T2- 50 MVA-200/20 kV, X=10% М-43.2 MVA, 18 kV, X-8% Line- 200 kV, Z= 120+j200 ohms. 2.
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct