"Please, the answer must be documented from abook, experience, or accurate information withoutusing artificial intelligence."Write an Arduino program to read the status of two pushbuttons connected to pins 2&3 respectively and flash ON twoLED's connected to pins 12&13 respectively according to thefollowing scenario: If pin 2 is HIGH let LED 12 flash withdelay of 400ms, and if pin 3 HIGH, let LED 13 flash ON withdelay of 300ms.

Firstly, we need to define the pins that we are going to use. In this case, we are using pins 2 and…

Answered: "Please, the answer must be documented…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 20RQ

See similar textbooks

Similar questions

1- Draw the complete circuit diagram that illustrates the experiment concept as in figure 5 by showing the pins number. Show the following in your plot (Arduino board, steppermotor coils and the driver circuit). Note: The drawing should be on paper and not with artificial intelligence, please.
I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards on top of the train. Broadcast communication (which involves radio frequency, not Wi-Fi) would help communicate about the train's lateness to five other wooden trains on the same track. Local communication would help communicate to the train station about the train's lateness. I would also need radio frequency Tx-Rx Modules for discharging and undergoing the signal, and repeaters just in case the signal loses power due to long-distance traveling. My wooden train should be automated. It should run at 4 inches per second, keep a minimum distance of 30 seconds away from the other wooden trains, and make a 17-second-long stop every 500 seconds. What's the procedure to connect the components? What's the Arduino code (C++) for this project?
I have an O Gauge track and would like to convert it into a “sensored” track. Additionally, I would like to connect that track to an ESP-WROOM-32 board that should flash an LED whenever the track detects a non-moving train. Please list all the components (and how many of each) needed. Also, what’s the procedure for connecting the components?
Write a program to flash three LED's connected to ports (8, 9 & 10) respectively as shown below: (Note: T₁-T3-5s & T₂=3s) LED, (pin 10) 2. Suen LED₂ (pin 9) LED, (pin 8) T₁'T' T'
Explain briefly about the the circuit diagram and explanation of the analysis of equations.
Show that Circuit (II) is simplified version of Circuit (I). Hint: Use reference table.
Q/ This means clarifying and indicating with I needd adrawind, anhotation and explanation of a picture Power Stage B IM A conduction Analog Interface Circuit To the gates. 介 Firing Circuit Micro-Controller Circuit C (A) fring angle (B) 30 firing angle (C) 90 firing angle (D) 120° fring angle Figure 7 Electronic Soft Starting & Effect of Firing Angle on Output Voltage
For a triac circuit shown in figure 5, determine the load current if the triac will turn on due to gate with Vin = 220V, 60Hz, R₁ = 40 ohms, and firing angle of 48 degree. A. 5.19A B. 4.43A C. 3.38A D. 7.21A
Question 5 What is the device address used by the instruction OUT A4, AL?
Consider the circuit with an RGB LED connected to Arduino as shown in figure 1: ⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀ na BERRETTU DIGITAL (PWM DIGITAL O UNO ARDUINO ARDUIND } POWE ANALOG IN BU E 322225 Local backup on RGB LED pins digitalWrite (5, LOW); delay(500); Red LED Blue LED Green LED void loop() { // put your main code here, to run repeatedly: digitalWrite (5, HIGH); delay(500); Arduino Pins Figure 1: RGB LED connected to Arduino Answer the following questions: a) Write a short code, configuring all the Arduino pins connected to LED as output. Pin 3 b) In the code snippet shown in figure 2, what color will be shown on the LED and for what duration? Note: All the LED pins are switched OFF initially. Pin 4 Ground Table 1: RGB LED pin connections to arduino Hint: Yellow coloured light is a combination of Green and red colour Pin 5 Ground Figure 2: c) Modify the code shown in figure 2, so that the LED turns ON as Yellow for 250 ms and then OFF for 750 ms. H 80
QUESTION 1 You wish to turn on two LEDs in the middle of the display, so the first thing you will do is set AL to _________. a 00 b 11 c 18 d 55 QUESTION 3 Signaling interrupts is an effective way to deal with interrupts if _______. a the microprocessor is dedicated to a task b a minimal number of chips is needed c polling is preferred d there are many devices installed on the system QUESTION 4 If an ISR is called as a result of the instruction "INT 32", then it is __________. a an invalid operation b a high priority interrupt c a software interrupt d a hardware interrupt
9) Answer the questions, in sequence, for the jump to-subroutine and return program in the figure below. Assume all switches are turned off after each operation. a. Switches S1, S3, S4, and S5 are all turned on. Which pilot light will not be turned on? Why? b. Switch S2 is turned on and then switch S4 is turned on. Will output PL3 be energized? Why? c. To what rung does the RET instruction return the program scan? 11 Ladder logic program Main program file 2 Inputs L1 Outputs S1 PL1 L2 too S1 PL1 S2 JSR O S2 JUMP-TO-SUBROUTINE SBR file number U:3 PL2 -S3 S3 PL2 H PL3- oo-S4 S5 PL4 -S5 PL4 Subroutine file 3 S4 PL3 SBR SUBROUTINE RET- RETURN

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS