9) Answer the questions, in sequence, for the jump to-subroutine and return program in the figure below. Assume all switches are turned off after each operation. a. Switches S1, S3, S4, and S5 are all turned on. Which pilot light will not be turned on? Why? b. Switch S2 is turned on and then switch S4 is turned on. Will output PL3 be energized? Why? c. To what rung does the RET instruction return the program scan? 11 Ladder logic program Main program file 2 Inputs L1 Outputs S1 PL1 L2 too S1 PL1 S2 JSR O S2 JUMP-TO-SUBROUTINE HE SBR file number U:3 PL2 -S3 S3 PL2 H PL3- oo-S4 S5 PL4 -S5 PL4 Subroutine file 3 S4 PL3 SBR SUBROUTINE RET RETURN

9) Answer the questions, in sequence, for the jump to-subroutine and return program in the figure below. Assume all switches are turned off after each operation. a. Switches S1, S3, S4, and S5 are all turned on. Which pilot light will not be turned on? Why? b. Switch S2 is turned on and then switch S4 is turned on. Will output PL3 be energized? Why? c. To what rung does the RET instruction return the program scan? 11 Ladder logic program Main program file 2 Inputs L1 Outputs S1 PL1 L2 too S1 PL1 S2 JSR O S2 JUMP-TO-SUBROUTINE HE SBR file number U:3 PL2 -S3 S3 PL2 H PL3- oo-S4 S5 PL4 -S5 PL4 Subroutine file 3 S4 PL3 SBR SUBROUTINE RET RETURN

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 1. Identify the items according to the illustration Controller Steam in Process Hot water out Steam…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: QUESTION 5 Explain the meaning of the following terms as they apply to a PID control: ✓ Process…

A: A PID controller is an industrial controller, which is used in control industries to regulate…

Q: ripple counter“

A: Counter- A device used for counting binary numbers is termed as digital binary counter. Digital…

Q: 1. What is the purpose of using digital to analog conversion? 2. What is the sign of the output…

A: Digital to analog conversion

Q: Determine the settings required for a PID controller which gave the process reaction curve shown in…

Q: What happened to the led speed blinking when the delay was changed?

A: /* Blinking LEDs- Program to run that the LED is connected to pin 6 and the delay is one second…

Q: The control circuit of a copier will be designed. There are 4 keys (S1,S2,53,S4) on the path of the…

A: Output assign to logic 1 for any of the two switch closed at a time but not s1 and s4 at same time…

Q: Identify the process happen in Figure Q29(a). Interrupt User Program Handler X Interrupt Handler Y

A: The process shown in fig. is defined as the bending waves around the corners of an obstacle or…

Q: Which type of device or system is used to set limits on a signal? A. DCS and PLC systems C. Selector…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 3. Solve the analog conversion for 8-bit binary numbers 101011112?

Q: Q1) Shows what happens during the interrupt cycle? Suppose that an interrupt occurs and R is set to…

A: In this question, We have to discuss about the interrupt cycle.

Q: Assume that you have only one push button and need to energize four LED Indicators as shown. Design…

A: Task: We have one push button and need to energize four led indicators.Pressed Once->Yellow…

Q: Design a PLC program that will correctly execute the following industrial control process: A part is…

A: We need to draw and explain the PLC diagram for the given operation. The given operation and…

Q: Interrupt Vector is basically a O A. indicator to CPU when interrupt occurs O B. Counter for…

A: The microprocessor can be interrupted from the normal execution of the instruction and asked to…

Q: Q1.) The state diagram for a negative edge triggered counter is shown below. Sketch the…

Q: Question 4: al Give four main characteristics of b1 Give four main programming languages of a PLC cl…

A: To write the four main characteristics of PLC (programmable logic controller)to give four…

Q: Red yelow and for 4-juactionr each junction with O Tratfic light lights. (ontro ller grean e 10…

Q: 4)A PLC scan cycle contains each of the following operations EXCEPT A)read inputs B)perform…

A: PLC's will work by scanning the program continuously, by doing this plc scans the hardware and…

Q: Q2: What is the maximum clock frequency that the control that can used? If time delay is 30 ns to…

A: Given time delay=30 nstransfer address=20 nsaddress register=20 ns

Q: 5. How you can operate a DC motor work with 3.7 volt ? Keep in mind that the motor is controlled by…

A: How you can operate a DC motor with 3.7 volt?Keep in mind that the motor is controlled by a…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A proportional system of control system. How to disable OFF-SET ? Draw example for Process line diagram and Controller line ?
I need the answer as soon as possible
Which one of the following is used to transform an electrical signal into physical output? a. Controllers b. Sensors c. LEDs d. Actuators
Find the resistance R. given the ohmmeter reading for each configuration of Fig. 10 www 1 ΚΩ www 2.2 ΚΩ www 1.2 ΚΩ A P U ASIA PACIFIC UNIVERSITY OF TECHNOLOGY & INNOVATION
What does the Arduino instruction pinmode do in the Traffic Light program?
Please answer this question fast.
What is the purpose of the break statement? Force the termination of a program. When a break statement is encountered in a loop, the loop terminates immediately and the execution resumes the next statement following the loop. To produce the systematic code, and the break statement does not affecting the program. To make the code easy to understand.
5
Solve only 4 please
Must answer all the questions.Dont attempt only one.i will dislike otherwise. Please help answer the following question regarding the PID controller. a) Define the meaning of the term "offset" b) Explain how offset can be reduced by adjusting the proportional action of controller c) State why (b) is not the best way of effectively dealing with "offset" AND Explain how "offset" can be reduced to zero.
Which of the following parameter will define the closeness of the measured value to the true value.? O a. Accuracy O b. Deadspace Oc. Precision O d. Sensitivity Identify the Control element in the given closed loop control system. Desired Output Flame Flame Brain Hands Regulator Eyes O a. Regulator O b. Eyes Oc. Hand O d. Brain
the controlled signals in control BD are then going to Select one: a. actuators b. sensors C. plant d. controllers the actuator requires a much higher primary voltage than 150v is Select one: O a Capacitive Discharge Ignition (CDI) O b. Inductive (Smart) O C. Peak and Hold O d. Inductive (Dumb)