C1 Input R1 22 ww R3 output Q1 R4 where R1 = 68KQ, R2 = 10KQ, R3 = 10KQ, R4 = 2000, R5 = 2.2KQ, C1 = 0.1uF, C2 = 0.1 uF Q1 = 2N3904 ⚫ Calculate what the expected DC voltage will be at the base: V₂ = ⚫ Calculate what the expected DC voltage will be at the emitter: V₁ = ⚫ Calculate what the expected DC voltage will be at the collector: Vc = Now create the circuit in Multisim and measure these voltages: VE = V₁ =. If the measured values differ more than +/- 20% recheck your calculations and measurements. Connect a signal generator to the input and set it for 50 mV Sine wave with a frequency of 10 kHz. Connect the output to a multimeter set to RMS voltage. Record the output voltage and frequency in the following table. Repeat the measurement for all given frequency values in the table.

C1 Input R1 22 ww R3 output Q1 R4 where R1 = 68KQ, R2 = 10KQ, R3 = 10KQ, R4 = 2000, R5 = 2.2KQ, C1 = 0.1uF, C2 = 0.1 uF Q1 = 2N3904 ⚫ Calculate what the expected DC voltage will be at the base: V₂ = ⚫ Calculate what the expected DC voltage will be at the emitter: V₁ = ⚫ Calculate what the expected DC voltage will be at the collector: Vc = Now create the circuit in Multisim and measure these voltages: VE = V₁ =. If the measured values differ more than +/- 20% recheck your calculations and measurements. Connect a signal generator to the input and set it for 50 mV Sine wave with a frequency of 10 kHz. Connect the output to a multimeter set to RMS voltage. Record the output voltage and frequency in the following table. Repeat the measurement for all given frequency values in the table.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter5: Components, Symbols, And Circuitry Of Air-conditioning Wiring Diagrams

Section: Chapter Questions

Problem 16RQ: Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load...

See similar textbooks

Similar questions

An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
INCLUDE ALL THE DECIMALS.
Question V.Full explain this question and text typing work only We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line
find the average power consume by RL for both fullwave and halfwave rectifier circuit.
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
For the circuit below and V1 waveform shown, plot Vout: U1 Vout OUT R1 OPAMP 1M V1 C5 20u Input voltage to circuit 15 12 6. 10 15 20 25 Time (msec) V1 (volts) 5/
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
I need the answer as soon as possible
question in photo please
Peak input voltage =(from graph) ?Peak output voltage = (from graph)?DC voltage across RL = ?ripple factor=?
Determine the waveform, theoretical, of the peak output voltage at Resistor L. 120 V rms 5:1 ooooo elele D₁ D3 D21 DA 4 R₁ WWW II Vout
LVDT produces an rms output voltage of 5.0 V for displacement of 3.5 mm. Calculate the sensitivity of LVDT please explain me