Repeat the example on symmetrical faults (page 27 in the class notes) if the fault occurs across the load terminals as shown below. 100 MVA, 11 kV Generator G + 0.05 pu. Reactance M 50 MVA, Motor 0.2 pu sub-transient On 100 MVA Base reactance 3 phase fault 0.25 pu sub-transient reactance The Motor is drawing 40 MW at 0.8 pf. Leading with terminal voltage of 10.95 kV. Calculate the total current in the generator and motor during 3 phase s.c. 27 27

Repeat the example on symmetrical faults (page 27 in the class notes) if the fault occurs across the load terminals as shown below. 100 MVA, 11 kV Generator G + 0.05 pu. Reactance M 50 MVA, Motor 0.2 pu sub-transient On 100 MVA Base reactance 3 phase fault 0.25 pu sub-transient reactance The Motor is drawing 40 MW at 0.8 pf. Leading with terminal voltage of 10.95 kV. Calculate the total current in the generator and motor during 3 phase s.c. 27 27

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.3MCQ: The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of...

See similar textbooks

Similar questions

Equal area criteria is a method used to calculate: Select one: O a. None of the answers b. Critical clearing angle and time for transient faults O c. Critical clearing voltage angle for transient faults d. Transient stability current limit O e. Steady state stability power limits
What is the difference between OLTC and transformers
The sequence components of the fault current are as follows: Ipositive = j2 p.u., Inegative = - j0.5 p.u. and Izero = -j 1.5 p.u. The type of fault in the system is
A 12 MVA, 132/6.6 kV, transformer having a reactance of 0.15 pu is fed from an infinite bus. The transformer feeds two motor each 6 MVA, 6.6 kV. Each motors has a transient reactance of 0.14 pu and a subtransient reactance of 0.30 pu based on its own rating. A three phase balanced fault occurs at the terminals of one motor as shown in the figure below. Find the subtransient fault current and subtransient current in breaker. M1) 132/6.6 KV СВ 38 CB Infinite Bus M2 Fault
pls solve it before 10 min
The reactance of the synchronous generator after sometime of the fault cleared is ............
q19/ choose the correct answer ..........................capacitors will supply reactive VAR during peak load condition and consumes reactive VARs during light load conditions 1- Booster Transformers 2- Shunt 3- Synchronous 4- Series
This question is about electrical power material and I want to solve it in 20 minutes
powe system Q8
A three phase fault is applied at the point P as shown in the figure. Find the criticalclearing angle for clearing the fault with simultaneous openings of the breakers 1 and 2. Thegenerator is delivering 1.0 pu at the instant preceding the fault
The bus bars of a power station are in two sections A and Bseparated by a reactor. Connected in section A are two 12MVA generators of 15% reactance each and to B, 8 MVAgenerator of reactance 10%. The reactor is rated 8 MVA and15% reactance. Two feeders are connected to bus bar Athrough transformers, each rated at 4 MVA and 5% reactance.Determine the maximum short circuit MVA with which circuitbreakers on the outgoing side of the transformers have todeal.
Q3/ For the system shown in figure. The generator is supplying 1.0 pu MW power under prefault condition. When three-phase fault occur at point F. What should the value of fault reactance must be to make the critical clearing angle equal to 58.9. Sc j0.1 j0.1 10.21 BE j0.38 38 j0.21 IEgl-12 pu 10.19 F 10.19 IVI-1.00 pu j0.1 j0.1 Q4/ Figure below shows the one-line diagram