During a stable transient event caused by opening and reclosing a circuit breaker to clear a fault, describe the angle 8 and the rate of change of this angle at the time instants when the potential energy of the rotor is zero.

During a stable transient event caused by opening and reclosing a circuit breaker to clear a fault, describe the angle 8 and the rate of change of this angle at the time instants when the potential energy of the rotor is zero.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.3MCQ: The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of...

See similar textbooks

Related questions

Q: An 8 pole single phase induction motor is running at 690 rpm.what is the slip with respect to…

A: Given: Rotor speed (N)=690 rpm Poles=8

Q: There are 144 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors…

Q: The principle of operation of a 3-phase Induction motor is most similar to that of a…

A: The 3-phase induction motor works on the principle of electromagnetic induction. It has both the…

Q: The rotor winding current for a four-pole synchronous ac generator with a distributed rotor winding…

A: the rotor winding current for a 4 pole synchronous ac generator with a distributed rotor winding…

Q: A 4 pole dc generator with duplex wave winding has 48 slots and four elements per slot. The flux per…

Q: Why is it necessary to conduct polarity tests on transformers?

A: Polarity test: It is a test conducted on primary and secondary winding of a transformer and to know…

Q: Do you think that a three – phase induction motor could be used to establish the phase sequence of a…

A: Yes, it is possible that a three- phase induction motor could be used to establish the phase…

Question

During a stable transient event caused by opening and reclosing a circuit breaker to clear a fault,
describe the angle 8 and the rate of change of this angle at the time instants when the potential energy of the rotor
is zero.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For 4 pole d.c machine armature winding with a double layer progressive simplex wave winding with 23 number of slots answer the following: a How many coils are present? b What is the coil span in terms of number of slots? c What is commutator pitch in terms of commutator segments? d How many coils are there between two consecutive commutator segments? e How many parallel paths are present?
The function of Copper shading band in induction type energy meter is to ensure flux produced by potential coil is exactly in quadrature with supply voltage. Select one: True False
common types of electrical failures of an AC induction motor
The brushes width in Wave winding is equal to a. 1.5 commutator segments. b. 1 of commutator segments. c. 1.25 commutator segments.
The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of an unloaded synchronous machine decreases from a high initial value to a lower steady-state value, going periods through the stages of __________ and ________ periods.
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
For a four pole, 16 slot armature with two coil-side/slot having wave connected progressive winding has single turn coils has simplex winding. The number of current paths is?
27. Which Arc Extinction Method operates by increasing the Arc Resistance by lengthening the Arc? A. Low Resistance Method B. Low Inductance Method C. High Inductance Method D. High Resistance Method
For the system shown in figure below, the per unit values of different quantities are E-1.2, V 1, X X2-0.4. Xa-0.2 Determine whether the system is stable for a sustained fault. The fault is cleared at 8-60°. Is the system stable? If so find the maximum rotor swing. Find the critical clearing angle. E25 G X'd 08 CB X2 F CB V28 Infinite bus
Q.4/ choose true or false: 1. The reluctance of any core is proportional directly with the length of it and inversely with both the permeability and the cross-section area of it. 2. The number of parallel paths in wave windings is equal to twice of the number of poles. 3. In dc machines with same values of Z, N, Ø, the emf for wave winding type is more than emf of lab winding type. 4. If we insert a current in such a conductor subjected to a constant magnetic field, a movement will achieved giving the principle of electric generator.
Problem 2 - A 1000 – MVA, 20 – kV, 60 – Hzthree-phase generator is connected through a 1000 – MVA, 20 – kVA/345 – kVYtransformer to a 345 – kVcircuit breaker and a 345 – kVtransmission line. The generator reactances are X = 0.15, Xa = 0.3, Xa = 1.4(pu) and its time constants are Ta = 0.05, Ta = 1.0, TA = 0.1(s). The transformer series reactance is 0.06pu; transformer losses and exciting currents are neglected. A three-phase bolted fault (solid 3-phase phase short circuit) occurs on the line side of the circuit breaker when the generator is operated at rated terminal voltage and at no-load. The breaker interrupts the fault 3 cycles after fault inception (neglect the effect of the transformer on generator time constants.) Determine the following (a) The subtransient current (p.u.) through the breaker (b) The sub-transient current (kA) through the breaker (c) The RMS ac (symmetric) fault current (p.u.) after 3 cycles
Whether a transformer shifts an ac waveform by 0° or 180° depends on the phasing of the waveform applied to the primary winding the amount of loading on the secondary winding the direction of turns of wire on the primary and secondary windings the type of core material that is used in the construction of the transformer