Sampling a continuous-time sinusoidal signal The plot below shows a continuous-time sinusoidal signal and a sampled version of that signal. The time axis is in seconds and the samples shown are taken at t = 0.3n for n = 0, 1, 2,.... What is the frequency of the signal in Hz? Round your answer (if necessary) to 3 decimal places. Do not put in units. Just enter a number. 0.5 0 continuous signal sampled signal -0.5 -1 0 0.3 0.6 0.9 1.2 t (seconds) 1.5 1.8 2.1 2.4 What was the sampling period used to obtain the sampled signal? Round your answer (if necessary) to 3 decimal places. Do not put in the units. Just enter a number. What was the sampling frequency used to obtain the sampled signal? Round your answer (if necessary) to 3 decimal places. Your answer should be in Hz. Do not put in the units. Just enter a number.

Sampling a continuous-time sinusoidal signal The plot below shows a continuous-time sinusoidal signal and a sampled version of that signal. The time axis is in seconds and the samples shown are taken at t = 0.3n for n = 0, 1, 2,.... What is the frequency of the signal in Hz? Round your answer (if necessary) to 3 decimal places. Do not put in units. Just enter a number. 0.5 0 continuous signal sampled signal -0.5 -1 0 0.3 0.6 0.9 1.2 t (seconds) 1.5 1.8 2.1 2.4 What was the sampling period used to obtain the sampled signal? Round your answer (if necessary) to 3 decimal places. Do not put in the units. Just enter a number. What was the sampling frequency used to obtain the sampled signal? Round your answer (if necessary) to 3 decimal places. Your answer should be in Hz. Do not put in the units. Just enter a number.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. For a sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 500µs/cm and the volt/cm switch is on 5V/cm. The width of one complete cycle is 4cm and peak to peak height is 5cm. Find for the waveform a) the frequency, b) the peak to peak voltage, c) the amplitude, and d) the r.m.s value
What is the DC equation and the waveforms?
0 9.20. In Figure P9.20, four discrete-time signals are plotted. Match each sinusoid listed below with one of the signals plotted in Figure P9.20. -10 -10 (a) x₁[n] = 3 cos (4πn) (c) x3[n] = 5 5 cos(4πn/8) Signal A in -5 0 n Signal C 0 16 5 5 10 10 3 2.5 2 1.5 1 0.5 0 -10 -5 -5 -10 -5 (b) x₂[n] = 5 cos (3πn) 5 sin (3πn) (d) x4[n] = Signal B 0 n Signal D 0 n 10 5 5 10 10 Figure P9.20
Give a detailed solution. Please need help
Ac - 100 VrmsR1 - 1kR2 - 500Rload - 1kCapacitor - 2uF Q1. How much is the capacitor voltage lagging from the AC source
A series L-R-C circuit consisting of a voltage source, a capacitor of capacitance C, an inductor of inductance L, and a resistor of resistance R is driven with an AC voltage of amplitude Vin and frequency omega. Define Vout to be the amplitude of the voltage across the resistor and the inductor. Find the ratio Vin/Vout.
A step-down chopper is to be used to supply power from a 600-V overhead wire to the commutator motor on a trolley bus. The motor may be mod- eled as a generated direct voltage in series with a resistance of 0.2 and an inductance of 25 mH. The frequency of the chopper is set at 500 Hz. (a) When the bus is stopped, what should be the ON time of the chopper to provide a motor current of 150 A? (b) What is the maximum possible generated voltage of the motor for which a current of 150 A can be supplied? (c) What is the average value of the supply current for the conditions of (a) and (b)? បទៅនឹងរស់របស (d) If the motor current is to be continuous, what should be its minimum. value?
1. Suppose that MATLAB is used to plot a sinusoidal signal. The following MATLAB code generates the signal and makes the plot. Draw a sketch of the plot that will be done by MATLAB. Determine the amplitude (A), phase ($), and period of the sinusoid and label the period on your plot. dt = 0.001; tt = = .05 dt : .15; Fo = 8; Z sqrt (2) * (1-j); xx = real( Z*exp( 2j*pi*Fo*tt ) ); plot tt, XX ), grid title( 'SECTION of a SINUSOID' ), xlabel('TIME (sec)')
i need help with part c
Example-3 Thank you
What is the ripple factor of a sinusoidal signal having peak ripple of 2V on an average of 50V? Show complete solution Round your final answer to the nearest hundredths.
A complex voltage waveform which has an rms value of 240V contains 30% third harmonic and 10% fifth harmonic, both of the harmonics being initially in phase with each other. (a) Determine the rms value of the fundamental and each harmonic. (b)Write down an expression to represent the complex voltage waveform if the frequency of the fundamental is 31.83 Hz.