Please show the solution and answers in each. Thank you. A 120 MVA, 19.5 kV generator has Xₛ = 1.5 pu and is connected to a transmission line by a transformer rated 150 MVA , 230 wye/18 delta kV Watts, and X = 0.1 pu. If the base to be used in the calculation is 100 MVA, 230 kV for the transmission line. a. Find the per-unit values to be used for the transformer and generator reactances. b. If the transformer delivers 80% of its rated capacity to the line at 220 kV, express the current in per unit. c. Find also the current in the genrator in amperes.

Please show the solution and answers in each. Thank you. A 120 MVA, 19.5 kV generator has Xₛ = 1.5 pu and is connected to a transmission line by a transformer rated 150 MVA , 230 wye/18 delta kV Watts, and X = 0.1 pu. If the base to be used in the calculation is 100 MVA, 230 kV for the transmission line. a. Find the per-unit values to be used for the transformer and generator reactances. b. If the transformer delivers 80% of its rated capacity to the line at 220 kV, express the current in per unit. c. Find also the current in the genrator in amperes.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
In developing per-unit equivalent circuits for three-phase transformers. under balanced three-phase operation. (i) A common Sbase is selected for both the H and X terminals. (ii) The ratio of the voltage bases Vbase/VbaseX is selected to be equal to the ratio of the rated line-to-line voltages VratedHLL/VratedXLL. (a) Only one of the above is true. (b) Neither is true. (C) Both statements are true.
An ideal transformer has no real or reactive power loss. (a) True (b) False
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
Single phase 10 kVA, 480 V / 120 V to feed a 120 V load from a 600 V source conventional transformer will be used. a. Draw the transformer connection that can do this job. b. In the connection you have drawn, the apparent power of the transformer (in rated operation state, the load power to be transferred) what happened. c. Calculate the maximum primary and secondary winding currents for the connection situation you have drawn.
Solve part c & d
Chapman Problem 3-4. A single-phase power system is shown in the figure below. The power source feeds a 100-kVA, 14/2.4-kV transformer through a feeder impedance of 38.2 + j140 N. The transformer's equivalent series impedance referred to its low-voltage is 0.12 + j0.5 N. The load on the transformer is 90 kW at 0.85 PF lagging and 2300V. а. What is the voltage at the power source of the system? b. What is the voltage regulation of the transformer? How efficient is the overall power system? С.
Consider the system shown in Figure 1. Assume the load voltage (VL) is 4720 V and the load consumption is 80 kVA at 0.85 lagging power factor. The line impedance (Zline) is 4.6+j8.5 2. The parameters of the 14,400/4800-V single-phase transformer referred to the secondary are: Req=0.95 , Xeq = 1.74 , Re = 48.5 kn, and Xm = 31.1 k. vp avs 4.6 +19.52 Zline Vs ~ P a:1 ele rmis alf Reais leee V₂ zí S Figure 1: System for Q1 I wad a) Find the current of the load. b) Find the primary and secondary voltages of the ideal transformer. nuomo I un cucc + Bline Xeq,s 1 V₂² 95, 74-32 1. VL 4720 Ponerlosture -> Pont IL = V₂ -V₂ Zine
A single-phase 100 kVA, 2400/240 V, two-winding transformer will be used as a step-down auto-transformer in a 2640/2400 V system. The connection diagram of the transformer is given below. Calculate the I1, I2 and Ix currents given in the figure. Compare the kVA values of the auto transformer with the kVA values of two-winding transformers.