Need correct handwritten solution Do not use chatgpt or any AI 5. Determine the equivalent admittance of the adjacent circuit inpolar form with the angle in units of degrees at a frequency of1 kHz. Then, use the admittance to find the impedance. Be sureto include units. (Hint: Admittance magnitude should bebetween 0.2 and 0.3 Siemens (S). Admittance phase angleshould be between 60 and 70°)b°R10ohmC68μFL820μH

Step 1: Step 2: Step 3: Step 4:

Answered: 5. Determine the equivalent admittance…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.5MCQ

See similar textbooks

Similar questions

I need the answer quickly
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load impedance.
Add the following two impedances (a) in series and (b) in parallel. Z1 = 4 + 3i and Z2 = 12 + 5i
Answer the question for all
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
(a) Transform v(t)=75cos(377t15) to phasor form. Comment on whether =377 appears in your answer. (b) Transform V=5010 to instantaneous form. Assume that =377. (c) Add the two sinusoidal functions a(t) and b(t) of the same frequency given as follows: a(t)=A2cos(t+) and b(t)=B2cos(t+). Use phasor methods and obtain the resultant c(t). Does the resultant have the same frequency?
Positive-sequence components consist of three phasors _________ with magnitudes and _________ phase displacement in positive sequence; negative- sequence components consist of three phasors with ________ magnitudes and _________ phase displacement in negative sequence; and zero-sequence components consist of three phasors with __________ magnitudes and __________ phase displacement.
QUESTION 19 E-06, PC-02. Three inductors 15 mH, 15 mH and 15 mH are connected in series. What is the total inductance? O 5 mH. Without knowing the coupling factor the total inductance cannot be found. 45mH. QUESTION 20 E-06, PC-05. Why are the iron cores of most induction coils laminated? To increase the core permeability. O To reduce the core reluctance. O To reduce the effects of eddy currents. Click Save and Submit to save and submit. Click Save All Answers to save all answers. MacBook Air 888 F7 FB F6 F4 F3 F2 & 23 $ 4 5 0 8 3 Y W E と S D S F G >> J しのくつつ >
Consider the network given in figure below, where the numbers indicate admittances in per unit. Find the admittance matrix. 1-12 2- j3 1- j2 2- j6 3. 3-j4 1-j4
The rated voltages of a single-phase transformer are 2000 V and 200 V in its primary and secondary respectively. The shunt impedance can be modelled with a resistance of 14000 ohms in parallel with a reactance of 1100 ohm, both refer to primary side. The primary and secondary series impedances are (0.12+j 0.35) ohms and (0.0012+j 0.0035) ohms respectively. A load is connected to the secondary side of transformer, draws 810 KVA with a lagging power factor of 0.85. The load voltage is same as rated voltage, that is 200 V. ▪ Use per unit method for analysis and find the voltage on primary side in pu.

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS