inch 1. In a coupled tanks system, we would like to change the water level in tank 2 from 4” to 2". We have recorded the water level in tank 2 as a function of time in the graph below. (20 pts) 3.5 3 2.5 2 1.5 4 1 120 130 140 150 160 170 180 190 200 210 S Please estimate rise time, percentage overshoot and steady state error from this graph.

inch 1. In a coupled tanks system, we would like to change the water level in tank 2 from 4” to 2". We have recorded the water level in tank 2 as a function of time in the graph below. (20 pts) 3.5 3 2.5 2 1.5 4 1 120 130 140 150 160 170 180 190 200 210 S Please estimate rise time, percentage overshoot and steady state error from this graph.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

Needing assistance with the attached pic.
What is the purpose of power factor correction to a given load? O To reduce the amount of voltage to the load. O To reduce the amount of dependence on automated machinery. O To reduce the amount of current to the load. O To reduce the amount of resistance of the load.
1/ Suppose that there are two types of H.V.T.Ls operating at the same voltage and carrying the same current, but one of them with smooth shapewhile the other with standard shape. Which of them, you will choose? a. choosing the smooth one. b. choosing the standard one. c. choosing the one with hollow construction shape. d. all these answers are wrong. 2/ As the ambient temperature in crease the disruptive critical voltage of coron a is: a. Decreased b. Increased c. No effect d. All these answers are wrong. 3/ Using HV underground cable improvevoltageprofile and power factor in any loaded inductive electrical grid because. a. Due to its inductive power effect. b. Due to resistive Effect. c. Due to its capacitive power effect. d. All of the above answers are wrong.
Discuss the effect of the value of K on the system in terms of Percentage overshoot, peak time, settling time, rise time and steady-state error and Use theory to determine the settling time and steady-state error for K = 15 and compare this result with that obtained from the simulation.
Solve both question.... It's objective type questions so as per bartlybe's guidelines you need solve both question.
For the system given below, a) Find K1 and K2 so that the steady-state error is zero, the settling time is one second, and the overshoot is 5% for a unit step input. b) Specify the system type and find the steady-state error a unit ramp input using the computed K1 and K2 values. "Can you explain step by step " check image "
please solve each part thank you i will like
I need the answer as soon as possible
Define the steady-state error, the settling time and the rising time.
A SERIES CIRCUIT CONSISTING OF AN 80- OHM RESISTOR, A 0.30 HENRY INDUCTOR AND A 50-uf (MICROFARAD) CAPACITOR IS CONNECTED TO A 120-VOLT 60+ CYCLE SOURCE C ALCULATE THE FOLLOWINC : (A.) EQUIVALENT IMPEDANC E OF THE CKT, (B.) CURRENT (c.) VOLTAGE DROPACROSS THE SEVERAL UNITS (D.) POWER AND POWER FACTOR,
A container equipped with a resistance heater and a mixer is initially filled with 3.6 kg of saturated water vapor at 120°C. Now the heater and the mixer are turned on; the steam is compressed, and there is heat loss to the surrounding air. At the end of the process, the temperature and pressure of steam in the container are measured to be 300°C and 0.5 MPa. The net energy transfer to the steam during this process is
Discuss the concept of load shedding in power systems. Under what circumstances is load shedding implemented, and what are the consequences of load shedding for consumers and the grid?