Need a sol What propagation of the data bits transmitted in a primary rate (E1) or US(DS1) PCM multiplex system is used for:-a) Frame synchronizationb) SignallingDifferentiate between single stage and multistage switching networks. Discussthe blocking conditions of two stage network.

Approach to solving the question: To solve the question, focus on providing a detailed explanation…

Answered: What propagation of the data bits…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Similar questions

What is an MSDS?
Q6: Sectoring is a way to do what? a. Achieve branch circuits. b. Put each phone call in a different time slot. c. Do SS7 look-ahead call placement. d. Partition Voice mail boxes e. It is an ISDN-PRI way of brining in trunks f. Achieve frequency reuse. g. None of the above
4. A data signal with bipolar voltage levels is shown below. The decision threshold is 0 volts. The logic levels are +1 volt for logic 1 and -1 volt for logic 0. Noise with the P.D.F. shown corrupts the signal. Find the probability of error at some instant of time on the condition that logic 0 is sent. LOGIC 1 +1 VOLT -2 1/2 دمت ~IN kla THRESHOLD +2 NOISE P.D.F. -I VOLT. LOGIC 0
Need a solufor number 2
理 QA Qs Je Qe Qc JA QA le Qc 5 Volts KAQA KeQc Clock Figure (23): Example (14) Synchronous Counter. Synchronous Counter Design Modification H.W.: Design a MOD-5, 3-bit synchronous counter to count in the following sequence: 2, 3, 5, 1, 7. To modify the design and minimize the additional gates required for the J andK inputs, route the unused states to their next natural count state. In other words, route 0 to 1, 4 to 5, and 6 to 7. 2. A synchronous counter of n flip-flop stages always has a modulus of 2". A synchronous counter must count binary numbers in sequence, either up or REDMI NOTE 9 PRO ACQUAD CAMERA Section Self-Test 1. A synchronous counter has a common clock input to all flip-flop stages rof the questions).
The entity declaration for the counter is: entity binary_counter is generic (n: integer := 4); port ( clk : in std_logic; cnten in std_logic; rst bar in std_logic; -- -- generic for counter width system clock -- enable counter count -- synchronous reset (active low) q out std_logic_vector (n-1 downto 0)); -- output end binary_counter; The alternative architectures for the counter must all be written in behavioral style. The four alter- native versions of the architecture are based on using either a variable or signal to store the count in the counter's description. One architecture must use an unsigned variable, one must use an unsigned signal, one must use integer variable, and one must use an integer signal. Write the four design descriptions for the counter. With the generic set to 4, use stimulators to verify the counter's operation for each design. Use a clock period of 100 ns for clk. Change the generic to 6 and verify that each of your descriptions gives you a 6-bit binary…
2. Complete the timing diagram for the AND gate below
Write VHDL code for a modulo-13 counter (counting sequence is 010, 110, …. 1210). The counter has the following features: a synchronous Active High Reset a value R can be loaded into the counter, using the signal Ld (Load) The signal Ld is active High Draw the schematic of your counter, showing the inputs and outputs. Show the number of bits for R, Q (output of the counter), Ld.
1. What is the modulo of the circuit below? 2. Make a table of the count sequence. 3. A BCD counter can assume____discrete state. 4. A BCD counter can divide its input frequency by____. 5. A four-bit binary counter contains the number 0100. Nine inpulse occur. The new counter state is_____. 6. Design a 4-bit down counter.
3 Consider the combinational circuit shown below. The propagation delay for each unit is indicated in ns. Assume all other delays are zero. 8 ns C(x,y) X 10 ns 10 ns y - 7 ns 5 ns 5 ns a) What is the latency and throughput of the circuit as shown? b) Indicate where storage registers should be placed to create a two-stage pipeline with maximum throughput. c) What is the latency and throughput of the two-stage pipeline in part b? d) What is the best throughput that can be obtained by pipelining? How many stages would this pipeline have?
Question 9 only
Q3. b) Suppose you want to transmit the 10-bit message [101101101] by Pulse code Modulation (PCM). Using clearly labeled diagrams, show the encoding the bit sequence using the following PCM waveform types: i) Bipolar RZ Signal ii) RZ-AMI iii) Bi – o - L iv) Delay modulation

SEE MORE QUESTIONS

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

SEE MORE TEXTBOOKS

What propagation of the data bits transmitted in a primary rate (E1) or US (DS1) PCM multiplex system is used for:- a) Frame synchronization b) Signalling Differentiate between single stage and multistage switching networks. Discuss the blocking conditions of two stage network.