Pb 8) 4.39For the C-clamp shown, what force F can be exerted by the screw if the maximum tensile stressin the clamp is to be limited to 30 ksi?F2 in.სის34361613blos 0101 alos12 nodus 121A (s3 in.in.16 in.16webleonas OFF elson yollA (d016 (& dof bolow-bloo ai 15912 020112LAsue) vilisub 22 bal.90Swman a bris ctxibasqqA) laste is tools?

Answered: Pb 8) 4.39 For the C-clamp shown, what…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Give me right solution
2) A machine frame is made of steel having Sy = 400 MPa and Ssy = 250 MPa. When loaded in a test fixture, the stresses were found to vary linearly with load. Two points on the surface were found to be most critical. With a 4-kN test load, stresses at these points were: point a, 0₁ = 200 MPa, 0₂ = 100 MPa; point b, 0₁ = 150 MPa, 0₂ = -100 MPa. Compute the test load at which the frame will experience initial yielding according to the (a) maximum-normal-stress theory, (b) maximum-shear-stress theory, and (c) maximum-distortion-energy theory. Discuss briefly the relative validity of each theory for this application. Considering all the information available, what is your best judgment of the value of the test load at which yielding would actually be expected to begin? 02= 100 MPa a 02 02=-100 MPa b 02 0₁ = 200 MPa 01 = 150 MPa
handwritten-solutions, please!
i need the answer quickly
3) A 10 kN-m torque, T, and a 50 kN axial load, F, are applied to the end of an aluminum 6063 tank containing compressed air under a pressure of 2 MPa. The tank has a 400 mm outer diameter and a 20 mm wall thickness. Aluminum 6063 has a yield strength of 48 MPa. a. Draw and label a stress element for the most stressed point on the tank. Explain why this is the most stressed point. b. Sketch Mohr's circle and find the principal stresses at the most stressed point. Make sure you label your axes! c. Determine whether or not this is a safe loading scenario by considering the max normal stress, max shear stress, and distortion energy. (Hint - calculate the factor of safety for each failure criteria) T
3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mm
The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin as shown. (Figure 1) Figure 1 of 1 > Part A If the wheel is subjected to a normal force of P = 3.3 kN, determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the wheel. Express your answer to three significant figures and include the appropriate units. Tavg= Submit Provide Feedback Value A Request Answer C Units ? Next >
Group5/Two fork end pieces are to be joined together by a single steel pin of 25mm diameter and they are required to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of either fork if the stress in the fork material is not to exceed 180 MN/m². What will be the maximum shear stress in the pin?
mecha
The schematic of a punch and die for punching washer isshown. Determine the force F needed to punch outwashers with thickness of 5mm, inside diameter of 15 mmand outside diameter of 25mm. The average shearstrength of the plate is 30 MPa and average compressivestress in the puncher is 65 MPa. Answer: F =___________________
ompletion QUESTION 8 The stepped down circular bar with diameters 2d and d is subjected to a tensile axial force aligned with its axis. The ratio of direct stress in segment AB to direct stress in segments BC is: OIE 2d O a. 2:1 O b. 1:4 Oc. 4:1 O d. 1:2 QUESTION 9 The segments AB and BC of composite bar constructed of the same steel have identical cross-sectiona in ouhinntod to a comnressive axial load. The ra
i need the answer quickly

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS