Strictly don't use chatgpt,I need FBD. Two steel plates are connected with (4) 3/4" diameter bolts, and a 70,000-poundtensile load is applied to the plate. What is the average shear stress in one bolt? Assume theshear force is evenly distributed between the bolts.SteelplateO

Step 1: Calculate the force acting on each bolt.F=470000F=17500lbCalculate the cross-sectional area…

Answered: Two steel plates are connected with (4)…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please refer to the images below for the problem
1.A 3inch by 3inch square steel guardrail post was hit by a car on one of its side and applieda 1.6 kN force. The base of the post is a ¼ inch thick square steel plate and is supported by four pieces half inch diameter bolts. (1 inch = 25.4 mm) a.Assuming that the bolts received an equally distributed force, what is the shear stress applied to a single bolt? b.If the bottomplate of the post is a steel with astress capacity of 120 MPa, what is the maximum allowable bearing force on the plate? c.Assuming that the post is a solid steel and was hit by a falling solid heavy object from above, what is the maximum load that it can carry? d.If the post is a steel tube withcircular hollow section and an outerdimension of 4 inch by 4 inch, what is the maximum inner diameterif same force was applied?
Answer both parts please! Part A. if the bolt is subjected to a compressive force of P= 21.3 kN, deteemine the magnitude of the average normal stress in the steel. Part B. if the bolt is subjected to a compressive force of P= 21.3 kN, determine the magnitude of the average normal stress in the bronze.
Question 2
This is mechanical engineering question. You must to answer it correctly using F-B-D Don't use chatgpt (Handwritten recommended)
If a 10kN load is applied on steel rod of diameter 10mm , the normal stress will be
A U-bolt supports a load of 5,000 lb. The cross-section of the bolt has a diameter of ½ in. How much stress is induced in the sides of the bolt? note: answer must be in ksi
Please give the given, required, and the solution. Draw the free body diagram and label properly.
4. Solve this with a clear solution to avoid confusion.
1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa, CALCULATE THE OUTER LENGTH OF THE SIDE OF THE PENTAGONAL TUBE IF THE INNER LENGTH OF THE ONE SIDE IS 40mm. 15,000N 15,000N 40mm CROSS-SECTION OF THE BRONZE ROD BRONZE ROD
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
Answer the problem. Show the full, complete and clear solution. Please provide a free body diagram.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Two steel plates are connected with (4) 3/4" diameter bolts, and a 70,000-pound tensile load is applied to the plate. What is the average shear stress in one bolt? Assume the shear force is evenly distributed between the bolts. Steel plate O