Problem 2 only, solve carefully, include the units and dra the diagram. Thanks! A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa, A. What tensile force applied each plate to shear the bolt, pounds?B. What bearing stress that the bolt can withstand, MPA 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850 in-lb. The shaft diameter is 1.75inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, findA. Force that will shear the pin, kNB. Shear pin diameter, mm2. A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa,A. What tensile force applied each plate to shear the bolt, pounds?B. What bearing stress that the bolt can withstand, MPA?3. In a 2.5 m cantilevered l-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress inbeam is 120 Mpa, determine theA. section modulus, in.B. The base and height of the beam if the base is 75% of its height, mm.

Answered: Image /qna-images/answer/97f230ea-80d7-4985-9cc8-ff6f24d1f66c.jpg

A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa, A. What tensile force applied each plate to shear the bolt, pounds? B. What bearing stress that the bolt can withstand, MPA

A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa, A. What tensile force applied each plate to shear the bolt, pounds? B. What bearing stress that the bolt can withstand, MPA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please help with solving.student no is 128425. please also draw fbd
use angle of 92 please
140mm $50 mm 100 mm | I kN In the figure, a force of 1 kN is applied by means of an arm connected to a shaft with a diameter of 50 mm. So, represent the stress state of point B on the element? b) Draw the Mohr's circle for the given stress member and calculate the principal stresses?
this question is not for a grade. it is only a study question. submitting it is not a violation of the honor code
A bandsaw manufacturer uses 10 inch diameter drums. If the allowable stress in the sawblade is 72 ksi, what is the blade thickeness? (Final answer in inches) +
Two plates are held together by 4, 28 mm diameter bolts. If a 25 kN load is applied to the plates in shear, what is the shear stress in the bolts in MPa?
Question 8 A metal cutter is used to chop metal sheets. The length of the metal sheets is 10000mm the width of the metal sheet is 40mm and the thickness of it is 4mm. If the shear force of the metal cutter is 8kN. Calculate the shear stress of the material.
5 decimal places 32. Two identical plates of 61 mm wide and 6 mm thick is connected by a square pin with side dimension 14 mm. If a plate is subjected to a tensile force of 29 kN, determine the maximum tensile stress (MPa) developed in the plate
The pressure in a cast-iron water pipe is 180 psi. If the inside diameter of the pipe is 15 in. and the allowable unit stress in tension is 2000 psi, what should be the thickness of a shell of the pipe, expressed as a multiple of 1/8 in. A. 3/4 in. B. 5/8 in. C. 1/2 in. D. 3/8 in.
Problem 1: The assembly below will be used for each problem. Lengths, diameters, and materials are provided. If the temperature when this system was assembled was 74F, what would be the stress in each cylinder at a temperature of 40F? Problem 2: If the fixed support at D were removed and the temperature change did not occur, how far would point D move if a 400 lb tension load was applied at the center of each cylinder? (Hint: what sections would you break up the assembly into to find the Normal forces?) Problem 3: Based on the results from problem 2 and the sections specified in your solution, how much would the diameter of each section shrink from the loads applied? (Hint: Look at Poisson's ratio for each of the sections listed. 304 Stainless steel 2014-T6 Aluminum C 86100 Bronze A 12 in. 8 in. D В C| 4 in. 4 ft 6 ft 3 ft