Can you please explain to me how you get this answer? Oil, with a vapor pressure of 20 kPa, is delivered through a pipeline by equally spaced pumps, each of which increases the oilpressure by 1.3 MPa. Friction losses in the pipe are 150 Pa per meter of pipe. What is the maximum possible pump spacing toavoid cavitation of the oil?▼ Answer8.6 km

Given, Vapor pressure of oil, pv = 20 kPa. Increase in pressure = 1.3 MPa = 1.3 × 106 Pa. Friction…

Answered: Oil, with a vapor pressure of 20 kPa,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the head loss due to friction of an oil of specific gravity 0.77 and viscosity 0.85 poise is flowing through a pipe at the rate of 3.7 m/s. Assume the pipe diameter as 29 cm and the length of the pipe as 5618 cm. Oil Density (in kg/m3) Reynold's Number - Co-efficient of friction - Head loss due to friction
Water flows through a 61-cm by 122-cm conduit at a flow rate of 2000 CMH. The horizontal conduit was 100 m in length and was made of sheet metal. Calculate the pressure drop (i.e. inlet pressure minus outlet pressure) in Pa. Take the dynamic viscosity of water to be 1.0 CP and its density to be 1000 kg/m³. Take the local gravitational acceleration to be 9.81 m/s².
A pipe is horizontal and carries oil that has a viscosity of 0.14 Pa s. The volume flow rate of the oil is 5.3 × 10^-5 m3/s. The length of the pipe is 38 m, and its radius is 0.57 cm. At the output end of the pipe the pressure is atmospheric pressure. What is the absolute pressure at the input end?
Verify that the flow of oil is laminar (barely) for an oil gusher that shoots crude oil 25.0 m into the air through a pipe with a 0.100-m diameter. The vertical pipe is 50 m long. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) (or 1.00 Pa.s).
Oil, with a vapor pressure of 20 kPa, is delivered througha pipeline by equally spaced pumps, each of which increases the oilpressure by 1.3 MPa. Friction losses in thepipe are 150 Pa per meter of pipe. What is the maximumpossible pump spacing to avoid cavitation of the oil?
Water flows from Reservoir A to Reservoir B. The pipe diameter D is 1 m, and the pipe length L is 300 m. H= 16 m, h = 2 m, and the pipe head loss is given by h₁ = 0.01), where U is the velocity in the pipe. In your solutions consider the head loss at the pipe outlet to be ( U² 2g (a) what is the discharge in the pipe? (b) What is the pressure at point P halfway between the two reservoirs? (c) sketch the HGL and EGL. Water D H P B
********** ********* Q2: The flow rate of liquid through pipe is 0.342 m³/s and the head loss per 100 m of pipe is 8 m. what is the diameter of the pipe? Kinematic viscosity v= 2*10$ m²/s, p=950 kg/m³ and equivalent roughness (ks= 0.06). *************************************************************** **************** *
Please find attached questions. Thank you.
A pipe is often used to assess the flow rate of water in the center of a pipe with an internal diameter of 102.3 mm at 20°C (density = 998.3 kg/m3, viscosity = 1.005 CP). The pitot tube coefficient is 0.98, and the manometer reading is 10 mm of mercury at 20°C (density = 13,545. 85 kg/m3). Compute the velocity at the center and the water's volumetric flow rate
What’s the answer for this please ?
1. The figure shows a type of flushometer in which the flat vane rotates on a pivot as it deflects the fluid stream. The fluid force is balanced by means of a spring. Determine the spring force required to hold the paddle in a vertical position when water is flowing at 100 gal/min. The diameter of the pipe is 1"
Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p°- 1.013*105 Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m Pail = 800 kg/m Pand = 200 kg/m P. h3=12 cm hg al2cm oIL Pa h25 cm ng = 6 cm %3D Sand water

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Oil, with a vapor pressure of 20 kPa, is delivered through a pipeline by equally spaced pumps, each of which increases the oil pressure by 1.3 MPa. Friction losses in the pipe are 150 Pa per meter of pipe. What is the maximum possible pump spacing to avoid cavitation of the oil? ▼ Answer 8.6 km