Link AC is made of a steel with a 65-ksi ultimate normal stress and has a ½½ x ½ -in. uniform rectangular cross section. It is 16 3 connected to a support at A and to member BCD at C by -in.-diameter pins, while member BCD is connected to its support at B by a 5 -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.35 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 8 in. B +in. C |6 in. |4 in.- P The largest load P that can be applied at Dis lb.

Link AC is made of a steel with a 65-ksi ultimate normal stress and has a ½½ x ½ -in. uniform rectangular cross section. It is 16 3 connected to a support at A and to member BCD at C by -in.-diameter pins, while member BCD is connected to its support at B by a 5 -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.35 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 8 in. B +in. C |6 in. |4 in.- P The largest load P that can be applied at Dis lb.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 14 × 1214⁢ × 12 -in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by 3838 -in.-diameter pins, while member BCD is connected to its support at B by a 516516 -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.05 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. The largest load P that can be applied at D is lb.
7
4: The boom AC is a 4-in. square steel tube with a wallthickness of 0.25 in. The boom is supported by the 0.5-in.-diameter pinat A, and the 0.375-in.-diameter cable BC. The working stresses are 25ksi for the cable, 18 ksi for the boom, and 13.6 ksi for shear in the pin.Neglect the weight of the boom.1. Calculate the maximum value of P (kips) based on boom compression and the maximum value of P (kips) based on tension in the cable.2. Calculate the maximum value of P (kips) based on shear in pin.
An aluminum alloy cylindrical roller with diameter 1.25 in and length 2 in rolls on the inside of a cast-iron ring having an inside radius of 6 in, which is 2 in thick. Find the maximum contact force F that can be used if the shear stress is not to exceed 4000 psi.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. A 2 kip/ft distributed load is applied on member AB, which is supported by a pin at A and bar BC. The connections at points A and B are shown in detail. All pins have a diameter of 0.5 in while all members have cross-sectional dimensions of 1.5 x 1 in. Determine the following:a. maximum normal stress in member BC (ksi)b. normal and shear stress in a horizontal section across member BC apart from the pin (ksi)c. shear stress in pins A and B (ksi)d. maximum bearing stress on member AB (ksi)
5: The structure shown was designed to support a30-kN load. It consists of a boom AB with a 30 x 50-mmrectangular cross section and a rod BC with a 20-mm-diametercircular cross section. The boom and the rod are connected bya pin at B and are supported by pins and brackets at A and C,respectively.1. Calculate the normal stress in boom AB and rod BC,indicate if in tension or compression.2. Calculate the shear stress of pins at A, B and C.3. Calculate the bearing stresses at A in member AB,and in the bracket.
Link AC is made of a steel with a 65-ksi ultimate normal stress and has a ½½ x ½ -in. uniform rectangular cross section. It is 16 3 connected to a support at A and to member BCD at C by -in.-diameter pins, while member BCD is connected to its support at B by a 5 -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.35 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 8 in. B +in. C |6 in. |4 in.- P The largest load P that can be applied at Dis lb.
Each of the four links in Figure has an 8x36mm uniform rectangular cross section and each of the other four pins has a 16mm diameter.a. Determine the maximum value of the average normal stress in the links connecting points B and D and points C and E.b. Determine the average shearing stress in points B and C.
Two ropes are used to hoist a 530 lb engine/transmission assembly as shown. The rope is anchored at C around the center part of the pin shown, causing the pin to experience a state of double shear. There is a frictionless pulley at A. The normal stress in the rope must not be allowed to exceed 15 ksi, and the shearing stress in the pin must not exceed 21 ksi. When the hoist is in the position given by: a = 44 in b = 11 ft c = 19 ft find the following: (a \& b) The forces carried in ropes AB and BC (c l& d) The necessary diameters of ropes AB and BC (e) The necessary diameter of the pin at C 2013 Michael Swanbom (a) TAB = (b) TBC = (c) dAB = (d) dBc = (e) d =
Problem 1: If the parts of the shaft below are a 1" diameter solid steel rod and a 2" OD diameter steel pipe with a 0.25" wall thickness, what is the torsional stress in each section of the shaft? B 6 in. 15 lb 8 in. 15 lb
Example 8 1-55: In the structure shown, an 8 mm diameter pin is used at A, and 12-mm- diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired. Top view k200 mm 180 mm 12 mm 8 mm B C B A B 20 mm 8 mm 8 mm 12 mm Front view Side view
Detailed steps for each answer